Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4946673.

This is a drill index for people with multiples of every size and need some way to organize them in a drawer or on a shelf.  
It happens over the years of buying smaller kits.  
There are sizing holes built in but you may have to enlarge them depending on your calibration level.

I just paused at height and changed the filament to white for the letters.  

Measures 275mm x 240mm x 30mm

Each pocket fits most jobber sized bits, some of my bits required a bit of grinding to fit...or they will fit eventually with enough sharpening

Multiple drill index  3/64" - 3/8"

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5175168.

I absolutely love the original design but I just had to make a couple tweaks to my liking.  


First tweak is to the duct itself.  The original I found the left side of my duct was drooping and sometimes would crash into my print, I taped it up for a bit but then modified the design to add another mounting tab where the fan shroud bolts on.  I just cut the one tab off the fan shroud with side cutters for clearance, I used a short m3 or m4 screw that just threaded right in there, it isn't tight but fit well enough to hold everything in place

Second is the endoscope mount.  The original one just didn't do it for me.  So here's another option.



BIQU H2 Fan duct tweaked (orig by fhogphil) 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4946678.

The mount for my generic chinese backup camera rusted away.  I made a new one.  Guaranteed to fit as long as you happen to have the same camera.  

Aftermarket backup camera mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4711931.

Just a remix.

The original had too small of a hook for my backpack to hang so I sketched a new one based off the orig idea.  Made it a longer hook and a bit wider.  It also takes a #8 wood screw as well now

Lay it on the side for printing.  I did it in PLA.  My walls are 3 layers thick so in my case infill doesn't matter...if you have less walls maybe 80% infill would suffice

Hook

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5190162.

Custom caddy for my sink and faucet.  Center hole is 68mm diameter so it should easily clearance most single faucets.  And my sink isn't anything special so it will probably work with yours as well

Fits both my sink plugs and a small sponge or whatever in the back

Sink caddy - dual holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4946662.

For removing the top cap of the oil filter housing on a 2005 Sunfire, probably will work for many other domestic vehicles around this era/make/model.

Require 3/8" drive ratchet and an extension of some sort.  I do have the correct size chrome socket in my toolbox but it was too deep and bulky to be useful.  This made the job quick and easy

I printed it with 6 outer walls and 50% infill out of petg.  Probably overkill but why not

Pontiac Sunfire oil filter socket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5175191.

Just tweaked the design slightly to fit my milwaukee m18 drill and impact driver.

I had to use a brim because I had trouble getting it to stick to the build plate but you can probably do without

Milwaukee M18 driver bit holder

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Schmooot

Achievements

Seedling

Debutant

Multiple drill index 3/64" - 3/8"