This model was designed to be a Halloween decorative jar. When printed with a light color filament at a low infill percentage, a light can be placed on the inside for a great accent lighting effect. The jar has a diameter of 75mm and a height of 135mm and is available in two different versions – one where the ghost’s eyes and mouth are holes or are not holes. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information.

Halloween Ghost Jar

Ghost Jar - Bottom - No Holes.stl

Ghost Jar - Bottom - Holes.stl

This model is meant to be used as a handle for any jar tops in the Rich 3D Designs store. All Jar Top Handles are attached using one (1) M3x16 bolt (M3x12 is also acceptable). These can be purchased inexpensively at any hardware store or Amazon. The bolt passes through the hole in the center of the Jar Top and screws into the hole in the bottom of each Jar Top Handle. It may take a couple attempts at first – the fit between the M3 bolt diameter and the hole in the Jar Top Handle is tight to ensure the handle stays secured. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Christmas Tree - Jar Top Handle

Jar Top Handle - Christmas Tree.stl

Christmas Present - Jar Top Handle

Jar Top Handle - Christmas Present.stl

Pumpkin - Jar Top Handle

Jar Top Handle - Pumpkin.stl

Jack-o'-Lantern - Jar Top Handle 

Jar Top Handle - Jack-o'-Lantern.stl

This model is meant to be used as a handle for any jar tops in the Rich 3D Designs store. All Jar Top Handles are attached using one (1) M3x16 bolt (M3x12 is also acceptable). These can be purchased inexpensively at any hardware store or Amazon. The bolt passes through the hole in the center of the Jar Top and screws into the hole in the bottom of each Jar Top Handle. It may take a couple attempts at first – the fit between the M3 bolt diameter and the hole in the Jar Top Handle is tight to ensure the handle stays secured. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.


Ghost - Jar Top Handle

Jar Top Handle - Ghost.stl

This model is used to store just about anything while also being aesthetically pleasing. The jar has a diameter of 95mm and is available in both short (80mm height) and tall (95mm height) sizes. The default sphere jar top handle is included in this model package. All Jar Top Handles are attached using one (1) M3x16 bolt (M3x12 is also acceptable). These can be purchased inexpensively at any hardware store or Amazon. The bolt passes through the hole in the center of the Jar Top and screws into the hole in the bottom of each Jar Top Handle. It may take a couple attempts at first – the fit between the M3 bolt diameter and the hole in the Jar Top Handle is tight to ensure the handle stays secured. Multiple Jar Top Handle versions are available for the Decorative Jar in the Rich 3D Designs store. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any extras tips. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Decorative Jar - Short & Tall

Tall Decorative Jar - Bottom.stl

This model is used to mount an arc style lithophane to a nightlight. The outlet prongs on the nightlight are used to hold the lithophone holder in place – so no damaging attachment methods are required. There are two version of this model – one that holds the lithophane from under the nightlight (bottom attachment) and another that holds the lithophane from the sides of the nightlight (side attachment). These two versions should support almost any type of nightlight on the market as well as keep the second plug accessible. The lithophane generated for this holder needs to be a specific width and shape. I used https://tool.itslitho.com to generate lithophanes for this project. The detail document given upon download of this file shows the settings I used – the only variable that can be changed from these settings is height and quality options or the lithophane will not fit the holder. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Lithophane Nightlight

Lithophane Nightlight - Side Attachment.stl

This model is used to keep your wedding ring secure while on the go. It attaches snugly to your Stanley Cup handle. The top of the ring holder securely screws on and off with a half turn. This model has two parts that must be printed separately. This is meant for both Stanley Cup handle types. Some have a smooth/rounded handle while others have one with edges. Pictures of the handle types are shown in the images of this model. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Ring Holder - Stanley Cup Attachment

Stanley Cup Attachment - Ring Holder - Bottom - Edge Handle - Rich 3D Designs.stl

This model is used to hang your keys while on the go. It attaches snugly to your Stanley Cup handle. It attaches snugly to your Stanley Cup handle. This is meant for both Stanley Cup handle types. Some have a smooth/rounded handle while others have one with edges. Pictures of the handle types are shown in the images of this model. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.


Key Hanger - Stanley Cup Attachment

Stanley Cup Attachment - Key Hanger - Edge Handle - Rich 3D Designs.stl

This model is used to hold your chapstick or lip gloss while on the go. It attaches snugly to your Stanley Cup handle. This is meant for both Stanley Cup handle types. Some have a smooth/rounded handle while others have one with edges. Pictures of the handle types are shown in the images of this model. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Chapstick Holder - Stanley Cup Attachment

Stanley Cup Attachment - Chapstick Holder - Edge Handle.stl

This model is used to secure a ring. It is shaped so that a ring with a diamond can be stored inside. When the carabiner clip is attached – the rings cannot be removed. The hole in which the carabiner clip is inserted has a 5mm (.20 in) diameter. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Carabiner Clip Ring Holder - Rich 3D Designs

Carabiner Clip Ring Holder - Bottom - Rich 3D Designs.stl

This model was designed to give the option to securely store a spare key and airtag without adding too much to the thickness of my Ridge wallet. Ridge and other 3D print shops do offer alternatives to this, but they are two separate products and take up too much room. This model must be combined with the elastic cash strap unless another means of attachment is determined. Money can also be placed in strap comfortably on top of the Ridge Wallet Key & Airtag Holder. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Ridge Wallet Key and Airtag Holder

Ridge Wallet Key and Airtag Holder - Rich 3D Designs.stl

This model is used to give the remote for your LED lights a home. I was getting tired of misplacing my LED light remote, so I created this as a solution. All you need to do to attach it to your light switch cover is loosen the screws, slide the tabs into place behind the light switch cover, and tighten the screws back up. This will fit most LED light remotes (53mm wide or smaller). There are two version of this print – one that attaches to the top of your light switch cover and another that attaches to the side of your light switch cover. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

LED Remote Holder - Light Switch Cover Attachments - Top and Side

LED Remote Holder - Light Switch Cover Attachment - Top.stl

This model is used to hang earrings of any kind from. Overall dimensions are 150mm tall by 100mm wide. The top right corner was left empty for any type of customization – vinyl, stickers, paintings, etc. – the possibilities are endless! An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information.

Earring Hanger Stand - Flower Design

Earring Hanger Stand - Flower Design.stl

This model is used to keep children from opening cabinet doors. It’s a very simple but functional design. The two holes for mounting have a 4.5mm (.177in) diameter. It is best to predrill the holes to keep the wood from backing out of the hole and cracking the print. Also be sure not to overtighten the screws to avoid cracking the print. This model has two versions – the “right” version is used for cabinet doors opened with your right hand, and the “left” version is used for cabinet doors opened with your left hand. The angle at which the child lock meets the cabinet frame varies between versions. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any other necessary information. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Cabinet Child Lock

Cabinet Childlock - Right - Rich 3D.stl

This model is used to give mason jar lids a place to live that doesn't take up counter or cabinet shelf space. This model has 3 countersunk 4mm (.157in) diameter holes for screws or can simply be adhered to a wall or cabinet door with sticky tack. I personally used gorilla mounting putty and it holds up great. An additional document will be included in the .zip file that gives more information on best settings when printing this model and any extras tips. Any questions before or after download can be sent to ask.rich.3d@gmail.com.

Mason Jar Lids Holder - Cabinet Mount

Mason Jar Lid Holder.stl

The COMMERCIAL membership allows members to sell physical 3D prints of 3D Rich Designs. One download is allowed per month and the commercial licensing terms are provided. If you have any questions, please contact us at ask.rich.3d@gmail.com. Thanks!

COMMERCIAL

A Rich 3D Designs membership includes more than a few monthly downloads - it offers you the ability to have your 3D model ideas brought to life by an experienced designer. With this membership, we offer you the ability to communicate with 3D modelers that can remix existing Rich 3D designs to your own personal specifications or create new models based on your own ideas.
The BASIC membership includes this and 3 monthly downloads. If you have any questions, please contact us at ask.rich.3d@gmail.com. Thanks!

BASIC

Short Decorative Jar - Bottom.stl

Decorative Jar - Top.stl

Jar Top Handle - Sphere.stl

I'm a creator with CAD and manufacturing experience that's always up for a challenge. If you have any questions or things you'd like me to model - email me at ask.rich.3d@gmail.com

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Rich 3D Designs

Achievements

Seedling

Pinned models

Decorative Jar - Short & Tall

Ghost - Jar Top Handle

Jack-o'-Lantern - Jar Top Handle

Christmas Present - Jar Top Handle

Halloween Ghost Jar

Christmas Tree - Jar Top Handle

Christmas Present - Jar Top Handle

Pumpkin - Jar Top Handle

Jack-o'-Lantern - Jar Top Handle

Ghost - Jar Top Handle

Decorative Jar - Short & Tall

Lithophane Nightlight

Ring Holder - Stanley Cup Attachment

Key Hanger - Stanley Cup Attachment

Chapstick Holder - Stanley Cup Attachment

Carabiner Clip Ring Holder - Rich 3D Designs

Ridge Wallet Key and Airtag Holder

LED Remote Holder - Light Switch Cover Attachments - Top and Side

Earring Hanger Stand - Flower Design

Cabinet Child Lock

Mason Jar Lids Holder - Cabinet Mount