Remix of Blank Love Locks for Remixing by DaveMakesStuff

Remix of Blank Love Locks for Remixing

Display only do not print.stl

Phelps3D_2theMoon.stl

For Christmas this year we were giving my nephew a Viewmaster. While there are plenty of discs out there, they seemed dated to me. So I went about trying to make my own by finding pics on the internet. These parts were designed so that I could cut the overhead projector sheet circles using an Exacto blade, the type with the flat tip, that was heated to allow it to be melted through the slot in the cutter part. I used a 5mm bolt and nut. The same base part us used to do the cutting on and then also used to as the bottom of the clamp which held the hand cut card stock discs together while the glue sets. These were printed at 0.28 mm layer height and 10% infill.

Homemade Viewmaster Disc Clamp and Cutter #thangs100k

ViewMasterBottomClamp (repaired).stl

This is a very little cup designed to allow you to put an air plant into it. Originally created this for my niece to use in her ice cream stick planter frame. Prints without need of supports, 0.2 mm layer height and 10% infill.

Air Plant Cup #thangs100k

I had someone give me a key that was exactly the same as my apartment key. I designed this and the Autobot one as a means to differentiate them. This fits one of those hexagon head type keys. I printed this at 0.2 mm layer height and 10% infill. Then you will need to superglue the two parts together before inserting the key into it. The hardest part about this design is being able to pry the key ring open enough to get it on. 

Transformers Decepticon Key Cover #thangs100k

DecepticonKeyCoverSideA (repaired).stl

I recently had someone give me a key exactly the same as my apartment key and wanted to make something that would differentiate them. This Transformers Autobot key cover is designed to be printed on an FDM printer with supports, 0.2 mm layer height, 10% infill. It fits one of those hex style house key heads. The two parts will need to be superglued together and then place the key in the slot. The hardest part about this is trying to pry the keyring open large enough for it to fit.

Transformers Autobot Key Cover #thangs100k

AutobotKeyCoverSideA (repaired).stl

Basically this idea came to me when I wanted to try to make a 3D printed helmet, but needed to be sure its dimensions would fit. You use a large metal yardstick and put one end on where the hole is then the other end slides over the metal yardstick. I printed the hole end standing up without supports and the other part on its long side so that it also does not need supports. Suggest 0.2 mm layer height and 10% infill.

Giant Caliper #thangs100k

This is the hole end of the giant caliper. Print it with the point sticking up without supports, 0.2 mm layer height, 10% infill. I used a 6 mm brim.

GiantCaliper4MetalYardstickHoleEnd (repaired).stl

These parts are to build your own DC Comics Batman Riddler's Cane. This is for the #Thangs3D #FranklyBuilt Superhero/villain Contest. Designed to use a painting shipping tube (approximately 28 mm ID, 30 mm OD and 70 cm long).   Due to problems with supports I decided to split the top in half so they could use less material.

RiddlersCaneTopPartB (repaired).stl

These parts are to build your own DC Comics Batman Riddler's Cane. This is for the #Thangs3D #FranklyBuilt Superhero/villain Contest. Designed to use a painting shipping tube (approximately 28 mm ID, 30 mm OD and 70 cm long).  

RiddlersCaneBottom (repaired).stl

3D Printing Nerd, been using FreeCAD since 0.13. Work with both FDM and Resin 3D printers. Can do commissions, but mostly non-organic models.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Phelps3D

Achievements

Seedling

Explorer

Debutant