The notch in the middle of the mount fits all Tooletries scrubbers while the hook can be used for other shower accessories.
 
**Print Recommendations:**
Print Material: PLA 
Infill Percent: 15% 
Perimeters: 2 
Layer Height: .2
Supports: NONE 
Print Orientation: Place the holder standing upright on the build plate (in the orientation in which it will be used).

**Additional Parts Required:**
	• Waterproof double sided tape - Amazon Link to 3M VHB Tape (https://a.co/d/aACaiWk)

**Assembly:**
	• Add the double sided tape to the holder before securing to your shower wall. 


Tooletries 2 in 1 Wall Mount

Tooletries 2 in 1 Wall Mount.stl

Watch stands are available in 3 versions: Upright, Minimalist, and Slanted (listed as separate models).
 
Print Recommendations: 
Print Material: PLA 
Infill Percent: 15% 
Perimeters: 3 
Layer Height: .2 
Supports: NONE 
Print Orientation: Place the side of the watch holder against the build plate. 

Additional Parts Required:
	• Double Sided Tape 
	• Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr (This adhesive twists off easily and doesn't leave residue.)
	
Assembly:
	• Add a small amount of double sided tape to the base of the watch mount to keep it secure during use. 

Watch Stand - Upright

Watch Stand Upright.stl

These T Handles are a must if you have found yourself dragging a paddle board up a beach.
 
**Print Recommendations:**
Print Material: PETG (this print relies on the high temperature resistance of PETG) 
Infill Percent: 25% 
Perimeters: 3 
Layer Height: .2 
Supports: NONE 
Print Orientation: Place the flat side of the t handle against the build plate.
Color Changes: The version pictured was printed with a color change after the first 10 layers and before the last 10 layers for a teal orange combo.

**Additional Parts Required:**
	• 1 ft of paracord/thin rope
	
	
**Assembly:**
	• Tie a knot in the paracord before threading it through the t handle. The knot fits inside the handle indent and you can tie the other end to your paddleboard or kayak.


T Handle for Paddle Boards, Kayaks

T Handle for Paddle Boards, Kayaks.stl

Whether the dog chewed your lens cap or it fell off a cliff getting that perfect shot, the solution is one print away.

Print Recommendations:

Print Material: PLA

Infill Percent: 15%

Layer height: .15 (a layer height greater than .15 will not work since this model requires a very precise fit)

Orientation: Place the top of the cap down against the build plate

Supports: NONE 

Lens cap for Canon EOS EF and EF-S lenses

Lens Cap for Canon EOS EF and EF-S lenses.stl

Designed to keep Blueland or other dissolvable tablets at the ready! 
 
**Print Recommendations:** 
Print Material: PLA 
Infill Percent: 15% 
Perimeters: 2 
Layer Height: .2 (larger layer heights will work just fine but will be more noticeable)
Supports: NONE 
Print Orientation: Place the bottom of the organizer against the build plate (essentially in the orientation that it will be used)

**Additional Parts Required:**
	• Double Sided Tape 
	• Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr (This adhesive twists off easily and doesn't leave residue.)
	
**Assembly:**
	• Add a small amount of double sided tape to the back of the organizer to make sure everything stays in place.


Soap Tablet Holder

Soap Tablet Holder.stl

Holds up to 4 blender bottle lids. If you drink your meals you know what this is about.


**Print Recommendations**

Print Material: PLA

Perimeters: 2

Infill Percent: 15%

Layer Height: 3mm

Supports: NONE

Print Orientation: Place the bottom of the model against the build plate.

**Assembly Instructions**
Place double sided tape on the base before firmly placing. See last photo for tape placement.
 
**Additional Parts Required**
Double Sided Tape

- Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

- This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Lid Holder for Blender Bottles

Lid Holder for Blender Bottles.stl

Sturdy 3 bag handle for one trip grocery runs.

**Print Recommendations**

Print Material: PLA or PETG

Infill Percent: 25%

Perimeters: 3

Supports: NONE

Carrying Handle for Grocery Bags

A formidable match for any post meal mess (yes, even that pan you've been soaking).

**Print Recommendations**

Print Material: PLA

Infill Percent: 25%

Perimeters: 3 

Supports: NONE

Dish Scraper

This is print in place model with integrated hinge that snaps closed. Fits cables up to 4mm thick.

**Print Recommendations**

Print material: PLA

Infill Percent: 15% 

Layer Height: .15 (a layer height greater than .15 will not work well since this model requires a very precise snap fit)

Perimeters: 2

Supports: NONE



Cable Clip

Converts your Magsafe Charger into a dedicated charging station. Ideal for desks and bedside tables.

Fits only the official Apple Magsafe charger.


**Print Recommendations**

Print Material: PLA 

Infill Percent: 15%

Layer Height: .2

Perimeters: 2

Supports: NONE

Print orientation: Place the dock with the base against the build plate (see Prusa Slicer file for reference.)

 
**Additional Parts Required**
Double Sided Tape Required

- Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

- This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Mount for Apple Magsafe Charger

Converts your Magsafe Charger into a dedicated charging station. Ideal for desks and bedside tables.

This print requires double sided tape. See Amazon link below for adhesive which doesn't leave residue. Folded over duct tape will work just fine if damaging the underlying surface is not a concern.

Fits only the official Apple Magsafe charger.


**Print Recommendations**

Print Material: PLA 

Infill Percent: 15%

Layer Height: .2

Perimeters: 2

Supports: NONE

Print orientation: Place the dock with the base against the build plate (see Prusa Slicer file for reference.)

 

Double Sided Tape Required

Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Horizontal, minimalist, and subtle (unless you print it in bright red of course).

This design is for the original PS5 version with disk. Print 2 long springs and 2 short springs.  



**Print Recommendations**

Print Material: PETG (this design relies on the semi flexible properties of PETG)

Infill Percent: 25%

Perimeters: 3

Layer Height: .3 

Supports: NONE

Print orientation: Place each spring sideways against the build plate.
**Assembly Instructions**

Attach double sided tape to each of the 4 springs. With the PS5 standing upright, place the 2 short springs near the base of the console (at each corner) and the 2 longer springs near the top. 


**Additional Parts Required**
Double Sided Tape Required

- Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

- This adhesive twists off easily and doesn't leave residue.

PS5 Horizontal Stand (for original disk version)

PS5 Stand Long Spring (2 Required).stl

Symmetrical belt or bag hanger designed to hook over curtain rods.

**Print Recommendations**

Print Material: PLA (anything with high rigidity will do just fine)

Infill Percent: 20% (this will easily hold belts and hangers)

Supports: NONE (give those snips a rest)

Belt Hanger Closet Hook

Symmetrical belt hanger designed to hook over curtain rods.

**Print Recommendations**

Print Material: PLA (anything with high rigidity will do just fine)

Infill Percent: 20% (this will easily hold belts and hangers)

Supports: NONE (give those snips a rest)

Belt Hanger

Nominal Brand Pro

Welcome to Nominal Brand

Nominal Brand Unlimited

3D geometry to catch drips with cork base to protect table tops.

Holder fits 4 coasters with cork bases OR 6 coasters without cork bases.

**Print Recommendations for Coasters**

Print Material: PETG (High temperature resistance of PETG is required for this design)

Infill Percent: 8%

Infill Type: Honeycomb

Top Layers: 0 (this is required to expose the infill)

Bottom Layers: 5 

Perimeters: 3

Layer Height: .15 

Supports: NONE

Color Change: YES. Change to a new color for the last 4 layers to achieve the same look as the model pictured.

**Print Recommendations for Coaster Holder**

Print Material: PETG (PLA will work just fine as well)

Infill Percent: 20%

Perimeters: 2

Layer Height: .15 (higher layer heights work as well, but layers become more visible)

Supports: NONE

**Additional Parts Required**
Cork Bases Required for each coaster

- Amazon link to pre-Cut cork bases (90mm diameter 2mm height) https://a.co/d/cpaK4Vd

Hex Coasters

Hex Coasters (Set of 4).3mf

Coaster Holder Prusa Slicer.3mf

Hang your Dyson attachments on any closet rod. Fits Dyson V7, V8, V10, V11, and V15 attachments.

**Print Recommendations:**

Print material: PETG (This design relies on the semi flexible properties of PETG)

Make sure the PETG is dry for this print so post processing with a pen knife is avoided.
Infill Percent: 20% 

Layer Height: .2 (layer heights larger than .2mm will not work for this model and will affect how the parts fit together)

Perimeters: 3 

Print Orientation: (see Prusa Slicer file for orientation)

Supports: No supports for the loop portion. The cylinder portion requires supports under the exterior pins (see Prusa Slicer file which includes paint on supports)


**Assembly Instructions**

Rotate the loop until it snaps onto the main cylinder. The loop is keyed so that in only fits on in one orientation. This ensures it does not pop off during regular use.

Closet Mount for Dyson Attachments

Mount for Dyson Attachments (Both Parts) Prusa Slicer.3mf

Preparing coffee should be as smooth as that first sip. This wall mount fits #4 and #2 coffee filters.

**Print Recommendations**

Print Material: PLA 

Infill Percent: 15%

Perimeters: 2

Layer Height: .15 (higher layer heights work just fine, but layers become more visible)

Supports: NONE

Print orientation: Place the top surface against the build plate

 **Additional Parts Required**

Double Sided Tape **Required**

- Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

- This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Coffee Filter Wall Mount (#4 and #2 filters)

Coffee Filter Wall Mount.stl

Versions included for the original Apple Magsafe puck and the new 1m/2m Apple Magsafe pucks (which have a braided cable). 
 
**Print Recommendations:**
Print Material: PLA 
Infill Percent: 15% 
Perimeters: 2 
Layer Height: .15 (larger layer heights will not work as this model requires a precise fit)
Supports: NONE 
Print Orientation: Place the bottom of the base against the build plate (essentially in the orientation that it will be used). Place the back of the Magsafe puck holder against the build plate.

**Additional Parts Required:**
	• Double Sided Tape 
	• Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr (This adhesive twists off easily and doesn't leave residue.)

**Assembly:**
	• Use a small amount of double sided tape to secure the base.
	• Lock the Magsafe puck holder into the base by rocking it in from the side.
	• Pop the Magsafe puck into place and push the cable in from the back.


Tip: Some PLAs will be affected by the heat of the Magsafe puck when charging, causing it to loosen in the mount. Secure the Magsafe puck with a small piece of double sided tape if you have this issue.


Standby Mode Magsafe Mount for iPhone

Modern Base.stl

Minimalist Base.stl

Puck Holder for New Magsafe.stl

Puck holder for Original Magsafe.stl

Functional, minimalist, and intuitive designs. 

Because optimization is a journey, not a destination. 

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Nominal Brand

Achievements

Seedling

Up and Coming

Pinned models