This is a magnet dispenser for 6X2mm magnets. 

Each dispenser can hold over 50 magnets. A magnet inserted into the slider allows for your 6X2mm magnets to follow the slider in either direction. The opening of the dispenser has a flanged lip. This is to keep your magnets from falling out if the dispenser is facing the floor and/or dropped. 

To dispense magnets, simply push on the Slider Plug toward the opening. 

Required Materials:
13G Filament
1 4X2mm Magnet

Assembly:
Insert 4X2mm magnet into Slider Plug.
Insert plug into dispenser with the magnet toward the opening.
Insert 6X2mm magnets into dispenser.


Happy printing!



Version Notes:
1.0 - Original.
1.1 - Fixed plug depth to make more comfortable.
1.2 - Added handle to slider plug to make it ergonomically make sense.
1.3 - Added flange to opening to make dispensing easier.
1.4 - Added magnet hole to slider plug to improve usability. 

6X2mm Magnet Dispenser

Magnet Dispenser 6X2.3mf

This is a Gridfinity Holder for the 6X2mm Magnet Dispenser

This holder can hold (yes I repeated the same word twice, shoot me) 4 dispensers. Need to hold more dispensers, simply print more holders. 

Required Materials:
28G Filament
4 6X2mm Magnets

Assembly:
Flip the holder over, so that it is face down a** up.
Press fit the 6X2mm magnets into their respective holes.
Fllip back over.
Drop into your Gridfinity Base.
Insert Dispensers.


Dispenser Info:

Each dispenser can hold over 50 magnets. A magnet inserted into the slider allows for your 6X2mm magnets to follow the slider in either direction. The opening of the dispenser has a flanged lip. This is to keep your magnets from falling out if the dispenser is facing the floor and/or dropped. 

To dispense magnets, simply push on the Slider Plug toward the opening. 

Required Materials:
13G Filament
1 4X2mm Magnet

Assembly:
Insert 4X2mm magnet into Slider Plug.
Insert plug into dispenser with the magnet toward the opening.
Insert 6X2mm magnets into dispenser.


Happy printing!


Version Notes:
1.0 - Original.
1.2 - Made compatible with new slider plug. 
1.3 - Made bottom magnet holes press fit to avoid the glue mess.
1.4 - Fixed press in magnet base hole shape. Was too tight.

6X2mm Magnet Dispenser Holder - Gridfinity

Magnet Dispenser 6X2 Holder.3mf

Magnet Dispenser Holder 6X2.stl

This is a stand for the Lenovo Legion Go. The intended use is to bring the Legion Go just above mixer/controller height. However, you can use this stand however you wish.

Some assembly is required. Please use the example photo for top and bottome placement. You will need 4 M3X8 Coarse Thread Screws, 4 M3X18 Screws with 8 matching Washers, and 4 matching Nuts. The larger tube joining the two bottom portions is held on by the 4 M3 Screw combo. The plugs are held in using the coarse thread M3 screws. Careful when screwing these in, as overtightening will strip the material. These can also be glued in place, but ensure not to get glue in the areas contacting the tubes.

This is version 1. As such, things may change in time. Feel free to remix this or leave comments for improvements you would like to see.

Happy Printing!

Legion Go - DJ Stand

Example.stl

This is a base station to turn your old cell phone into a touchscreen to control your printer with the Bambu Handy App.

The base opening is enlarged, so you can design a plate for any phone to slide inside. For charging, use any 180 degree USB C or Lightning adapter. The specific adapter I used can be found here. You can modify the square plug to fit any adapter you purchase. Or, you can fill the void with hot glue. The choice is yours. Chaotic evil, or boring neutral.

In this example, I am using a Redmi Note 8 Pro. It is a decently powerful Android Phone that can be found for less than a hundred bucks.

Myalteredsoul

Achievements

Seedling

Pinned models

Legion Go - DJ Stand

6X2mm Magnet Dispenser

6X2mm Magnet Dispenser Holder - Gridfinity

Legion Go - DJ Stand

Bambu Phone Base