Within minutes, you will get a way to hang anything on the wall... in two ways, visible and hidden

You can use adhesive to attach it, double-adhesive tape, or a stapler

There is a line for balance... and the hidden one needs A little heat to bend...and no need for support

4 files, 1 and 2 for light weight and 1 A and 2 A for heavier weight

Hang it 

Hangit 2.stl

Another Mobile stand ...... It's complicated that is true....but maybe it's faster to print....and definitely smaller when folded....try it and you'll know.

Print in place ..... No support 

Mobile Stand Foldable

MBF.stl

Small Vise... with high and low clamps.... and holds different thicknesses... 1 - from 2 to 6..... 7 - from 8 to 12.... and 13 - from 14 to 18  ..... Print what suits your use

No screws, nuts or anything.....just press it in from the sides

Print in place ..... No support 

Quick Vise

Quick Vise 13 G.stl

I don't know for what to use it ... Maybe a candle base... or a small table... you need 12 bamboo sticks, 5mm in diameter and 127mm long...and drops of glue.

Something Twisted

ST2.stl

In 15 minutes or maybe less - depends on your printer - you get a UKB holder...... The parts are.... the holder body and the cover.

UKB Holder

UKB   B1.stl

Maybe it is useful for storing a single pill in the key chain ...or checking the quality of the printer and its settings...I don't know, you decide.

Dimensions of the box are 20x20x20 mm

Sliding Box 

SB A.stl

2.5mm -3mm - 4mm and 5mm Cross Spanner ..... with 1/4 hex bit holder and  a key chain 

Small Cross Spanner

SCS.stl

Another screwdriver....but this time it is square....and there is storage for two bits....without support and print in place....use more than two walls for strength

For 1/4 inch bits ......  key chain


Square Screwdriver

Square Screwdriver.stl

A box that can be opened and closed with a lever from the bottom...... Easy to print and without support.... All you need... 2 pins, 5 mm in diameter and 22.5 mm long..... and drops of glue.
I used bamboo sticks with a diameter of 5 mm. If you have  -  spring - it will close more easily.

Ladybug Box

LB G 2.stl

I don't know the best use for it yet, but it might be useful to someone. No support, just a M4 screw and  nut.

I used filament to connect the legs

Mini Pulley Puller

MPP 1.stl

A new idea...maybe.....simple and can be attached to a key chain

No support ..... Print in place 

Use more than two walls - Perimeters - for strength 

For 1/4 inch hex bit


Folding Screwdriver Handle 

FSHN.stl

I know the name is funny......but something new to the printer tool.....easy to print and almost fast

AKH1 ...... New version... with -  a clasp at each end to latch them when rolled up


Articated Allen Key Holder

AKH1.stl

In less than 17 minutes you have a  Clip with button ...... I know it will break after a while ...... but you can print another one

This is an experiment

Cable Clip With Button

CCWB.stl


A small spatula and a plate ...... for mixing small amount of glue ..... card size 

fast and useful

Glue Card

GC 1.stl

In 5 minutes or less a key chain ring ..... you need a piece of filament 70 mm long for the inside ring and that is it

No ......support



Keychain Ring 

Keychain Ring  R.stl

You need .... 11 pins 10 mm L X 2 mm D... for the pins I used nails .....and  1 M6 screw and nut  and  glue

The pins are for strength and safety

No support .... use more than two walls - Perimeters - for strength 

OLFA 25mm Blade Holder

NOH 2.stl

Small and fast to print..... there is storage for 4 bits 

for 1/4 inch hex bits
 

You need two magnets   3 X 3 mm  

No support .... use more than two walls - Perimeters - for strength 

Double Ended Screwdriver

DES V2.stl

Another - Nipper Cutter Holder   ..... But perhaps faster, more practical, and more stable

For the nipper cutter with the printer

 V2 - Smaller and faster .....No support

Nipper Cutter Holder

NCH 2.stl

The same rotating box as before, but with double drawers..... The 5 mm pins length are as follows..... 1X 60mm .... 4x 45mm.... 8X 17mm 

No support...just a gap at the top 0.6 mm so it can spin freely ..... and drops of glue

I used bamboo stick 5 mm as a pins

Double Rotating Box

DRB BC1.stl

You need 9 pins with a diameter of 5 mm and in the following lengths: 1X - 33 mm for the center, 4X - 23 mm for the edges, and 4X - 16 mm for the circle

That's all......No support...just a gap at the top 0.6 mm so it can spin freely ..... and drops of glue

I used bamboo stick 5 mm as a pins


 Rotating Box

RB BC.stl

Rotating Fish Yin yang keychain .... very fast to print Needs some smoothing and glue .... easy to assembly

Rotating Fish Yin yang keychain

1.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Muh60

Achievements

Seedling

Fan Favorite