Stand to hold rolling paper at a 90 degree angle for easier loading. Supporting section is 100 mm long, so, should work well for king size (110 mm) length papers. If anyone wants this in a different length, it would take me under a minute to make, so, feel free to let me know.

Rollhorse 140 mm

Rollhorse_140mm.stp

3D printable piece, designed to work with the flywheel puller metal part made by Fetteworst, to pull any Daybreak, Kepler or Pulsar wheels (or any other wheels with the same top geometry) off a motor shaft, without risking bending the motor shaft, or applying force to the flywheel cage.

Metal part can be found here: https://www.etsy.com/listing/744330014/nerf-flywheel-puller

Flywheels are sold by Kuryaka through Etsy, and various resellers (FoamBlast, Out of Darts, Blaster-Time.eu, ...): https://www.etsy.com/shop/KuryKafe

M5 hex nut included with this should be a nice friction fit in the printed part.
Slip over top of flywheel, rotate metal part (internal hex driven) to pull the flywheel straight up off the motor shaft.

Flywheel puller for Kuryaka flywheels (Daybreak, Kepler, Pulsar)

Loud two-tone whistle that incorporates the "awesome face" emoticon in its design. Color changes at certain heights could be used to achieve a multi-color print with different colors in different areas of the face.

"Awesome face" whistle

Jig for cutting 3 mm round stock - I used carbon fiber rods, but anything sufficiently rigid should work - to the right lengths to reinforce a Nerf N-Strike Recon shoulder stock.

Cut four pieces at each length, total length of all the bars is 600 mm, so, round stock of just over 600 mm is required, to account for the width of the cutting tool. After each cut, use a thin screwdriver, or straightened out paper clip or similar, to push the rod out of the jig. Attach to the plastic bars in the shoulder stock using epoxy, or a different suitable adhesive.

All tools and parts used shown in uploaded picture, also showing dry fit of the cut rods in the stock.

Nerf Recon stock reinforcement rod cutting jig

Jig for cutting 3 mm round stock - I used carbon fiber rods, but anything sufficiently rigid should work - to the right lengths to reinforce a Nerf N-Strike Recon shoulder stock.

Cut four pieces at each length, total length of all the bars is 600 mm, so, round stock of just over 600 mm is required, to account for the width of the cutting tool. Attach to the plastic bars in the shoulder stock using epoxy, or a different suitable adhesive.

All tools and parts used shown in uploaded picture, also showing dry fit of the cut rods in the stock.

Nerf N-Strike Recon stock reinforcement rod cutting jig

No tools or cutting required. Screws optional.

Nerf Stryfe 0.36 inch voltmeter mount

Stryfe 0.36 inch voltmeter mount

Nerf Stryfe 0.28 inch voltmeter mount

No tools or cutting required, screws optional.

Stryfe 0.28 inch voltmeter mount

150 mm long. Use 5 mm dowels of some sort to connect the two pieces. I used 5 mm aluminium tubing. Uses the stock pump grip screws.

Zuru X-Shot Chaos Orbit picatinny adapter pump grip replacement - 150 mm

Jig to cut 5 mm OD material to the right length for the pump grip.

OrbitPump15mmBarCuttingJig.stl

120 mm long. Use 5 mm dowels of some sort to connect the two pieces. I used 5 mm aluminium tubing. Uses the stock pump grip screws.

Zuru X-Shot Chaos Orbit picatinny adapter pump grip replacement - 120 mm

90 mm long. Use 5 mm dowels of some sort to connect the two pieces. I used 5 mm aluminium tubing. Uses the stock pump grip screws.

Zuru X-Shot Chaos Orbit picatinny adapter pump grip replacement - 90 mm

Nerf Rival Kronos jam door with hole

No shell cutting required, replaces the sliding doors at the bottom of the priming slide. Undo the four screws on the slide, pull out the doors, put in the T-pull, assemble again.

Printing requires support for the tabs on the sides.

Nerf Rival Kronos T-pull - same width as Kronos shell

No shell cutting required, replaces the sliding doors at the bottom of the priming slide. Undo the four screws on the slide, pull out the doors, put in the T-pull, assemble again. Extra wide for the heaviest of primes.

Printing requires support for the tabs on the sides.

Nerf Rival Kronos T-pull - wide

Piece that fits a Nerf magazine to turn it into a stand for your blaster. Works with any straight magazine, not the curved "banana" magazine or drums. Extra large footprint for unbalanced blasters. Can keep a Titan CS-50 balanced. Has the Belgian Foam Flingers labeling.

Nerf magazine stand XL (BFF)

Nerf magazine stand extra large (BFF)

Piece that fits a Nerf magazine to turn it into a stand for your blaster. Works with any straight magazine, not the curved "banana" magazine or drums. Extra large footprint for unbalanced blasters. Can keep a Titan CS-50 balanced.

Nerf magazine stand XL

Piece that fits a Nerf magazine to turn it into a stand for your blaster. Works with any straight magazine, not the curved "banana" magazine or drums. Has the Belgian Foam Flingers labeling.

Nerf magazine stand (BFF)

Piece that fits a Nerf magazine to turn it into a stand for your blaster. Works with any straight magazine, not the curved "banana" magazine or drums.

Nerf magazine stand

Jig to cut .50 caliber foam darts to 1/3 length. Insert tip first, and use a sharp blade.

Nerf Elite third length dart cutting jig - 24 mm

Jig to cut .50 caliber foam darts to 1/3 length. Insert tip first and use a sharp blade.

Jig to cut .50 caliber foam darts to just over half length, matching the size of Worker's short darts. Insert tip first, and use a sharp blade.

Nerf Elite half dart cutting jig - 38 mm (Worker size)

Jig to cut .50 caliber foam darts to half length. Insert tip first, and use a sharp blade.

Nerf Elite half dart cutting jig - 36 mm

Jig to cut .50 caliber foam darts to half length. Insert head first, and use a sharp blade.

Insert MEGA dart tip first, use a sharp blade of sufficient length and cut the darts down to half size. Back half of the foam can be used with an inserted .50 caliber dart (cut to appropriate length) as a second projectile. Insert foam from .50 caliber dart before cutting to increase the weight, if desired.

Nerf MEGA half dart cutting jig

Jig to turn 25 half-length foam darts into "bamboo" darts. Use without heat and just leave the darts in, or print in a material that can handle a bit of heat and use a hair dryer to help things along. 1.2 mm walls, so, designed with .4 or .6 mm extrusion width in mind.

Half-length foam dart bamboozler - half dart bamboo forming jig

Jig to turn half-length foam darts into "bamboo" darts. Use without heat and just leave the darts in, or print in a material that can handle a bit of heat and use a hair dryer to help things along.

36mmDartBamboozler_x25.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

MrJelle

Achievements

Seedling

Debutant

Voyager