Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5809206.

This is v2 of my microSD card holder. Depending on the adapter you need for your PC, you have to select the right bottom part.

As the adapter vor USB-C got smaller, the box is smaller as well. For standard USB the box is a little taller to fit the new adapter.

The first bottom part is for a USB-C adapter.
http://bit.ly/3D9sOiV

The second bottom part is for a normal USB adapter.
http://bit.ly/3kDu0Vi

MicroSD Card holder v2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5778276.

This is a chassis for 1/43 scale bodies like Carrera Go, SCX Compact or other bodies.

With this chassis you can convert almost every 1/43 scale car to a RC car. 

BOM and build instructions are on instructables.com
https://www.instructables.com/RC-Car-Chassis-for-143-Scale-Bodies/

https://www.youtube.com/watch?v=VIx1F1QALw8

https://youtu.be/UvDYX6JVg88

https://youtu.be/svXnV8w0wfA

RC Car chassis for 1/43 scale body

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2952852.

It's finally here. Version 2.0 of the FPV-Rover.

This is the second version of the FPV-Rover. 
https://www.thingiverse.com/thing:1240754

This one is with 540 motor (brushed and brushless). This was requested a lot on the other version and I redesigned the whole rover (although it looks the same) for this change.

<h3>Intructions and BOM can be found on Instructables</h3>
https://www.instructables.com/id/FPV-Rover-V20


<h3>All upgrades from V1 can be used for V2.0 as well.</h3>

Upgrade 01 (rubber gun):
http://www.thingiverse.com/thing:1269962
Upgrade 02 (trailer):
http://www.thingiverse.com/thing:1700138
Upgrade 03 (GoPro mount):
http://www.thingiverse.com/thing:1936491
Upgrade 04 by Superfly851 (grabatron):
http://www.thingiverse.com/thing:1979227
Upgrade 05(Nerf Dart Launcher)
https://www.thingiverse.com/thing:3835285
Upgrade 06 (Snow Plow)
https://www.thingiverse.com/thing:4630222

Videos on Youtube:
https://youtu.be/dpUSdjNppN0
https://www.youtube.com/watch?v=lbQW_ebiLKA
https://youtu.be/6aBkTEbLCWM (camera tilt)
https://youtu.be/Bfb7bcftKTg (testrun on balcony)
https://youtu.be/AgPFbaMxf3g (Nerf Dart Launcher)
https://youtu.be/ULYmqGeH-P4 (Snow Plow at work)


Latest update: 30.09.2020

FPV-Rover V2.0 (RC Tank)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5660965.

This is a remix of the race truck body by MarkerDave created for the WLToys K989 1/28th scale RC car (http://bit.ly/3ur6jBr).

I've added some details to the body, closed the holes in the front and made it lighter. Width is 75mm.

The body can be mounted perfectly to the chassis.

Print it with 2 perimeter and 15% infill. 

The three parts, cabin, left and right have to be glued together. Remove the original front bumper and attach the front mount to the chassis.

https://www.youtube.com/watch?v=GvUaKxxDXuk

RC Race Truck body for WLToys K989

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1700138.

This is a remix of the OpenRC Truggy designed by Steamerzone.
http://www.thingiverse.com/thing:378042
The tires are a remix of the small tire by Bastien.
http://www.thingiverse.com/thing:626863

It is designed for the FPV-Rover (V1.0)
http://www.thingiverse.com/thing:1240754

And for the FPV-Rover (V2.0)
https://www.thingiverse.com/thing:2952852

Follow us on http://fpv-treff.de/viewtopic.php?t=7615

https://www.youtube.com/watch?v=n8MtFnkzye0

Trailer for the FPV-Rover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2343612.

This is a replacement silicone cover for the original E3D V6 (new version).
The original cover does not stay where it should be.

Just print all 3 parts, connect them and mold your cover.

Instructions:
Print everything with about 20%-25% infill. You should print the parts with 0.1mm layer height for a smoother finish.

To fill the silicone into the mold I use these needles and a normal syringe
http://bit.ly/3Fx9dtq

Wait about 2 hours till the silicone is dry to clean everything.

BOM:
4x M2 x 8mm screw
https://bit.ly/3UpC1tr

4x M3 x 8mm screw
https://bit.ly/3izqOcy

1x 6mm metal pipe

1x silicone (shore 33 up to 450 degree Celsius)
https://goo.gl/yVxw4y

E3D v6 (new version, cartridge thermistor) Silicone Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3669829.

What do you do if you have spare parts from another RC project? Right, build another one.
I decided to build a RC car. But it shouldn't be just a standard RC car. Therefore I've designed a trike with a rear steering wheel.

Intructions and BOM can be found on Instructables
https://www.instructables.com/id/RC-Trike-With-Rear-Steering-Wheel

Instructions for the Nerf Dart Launcher
https://www.instructables.com/id/Nerf-Darf-Launcher-for-the-FPV-Rover/

Videos:
https://youtu.be/wLeIawSgQNw
https://www.youtube.com/watch?v=rRQhDsAibac
https://www.youtube.com/watch?v=q4DoK8gZ2og&t=1s

The first Ad-On for the Trike, a Nerf-Dart-Launcher
https://www.thingiverse.com/thing:3835285

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

<h2>Parts to print</h2>
I've printed all parts (beside the tires) in PETG. But any material is fine here. Tires are printed in TPU.

<ul>
<li>1x Body</li>
<li>1x Top part 1</li>
<li>1x Top part 2</li>
<li>1x Front fender left</li>
<li>1x Front fender right</li>
<li>1x Rear fender</li>
<li>1x Servo arm</li>
<li>2x Servo extension</li>
<li>1x Rear wheel attachment (Support needed)</li>
<li>1x Rear wheel</li>
<li>1x Rear tire (use TPU)</li>
<li>2x Front wheel</li>
<li>2x Front tire (use TPU)</li>
</ul>

RC FPV-Trike with rear steering wheel

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1240754.

It's finally here. The new FPV-Rover V2.0
https://www.thingiverse.com/thing:2952852


This is a remix of the drogerdy designed by timmiclark.
http://www.thingiverse.com/thing:700835/#files

Upgrade 01:
http://www.thingiverse.com/thing:1269962
Upgrade 02:
http://www.thingiverse.com/thing:1700138
Upgrade 03:
http://www.thingiverse.com/thing:1936491
Upgrade 04 by Superfly851:
http://www.thingiverse.com/thing:1979227
Upgrade 05(Nerf Dart Launcher):
https://www.thingiverse.com/thing:3835285
Videos on Youtube
https://www.youtube.com/watch?v=4Qc0D7U5R0s
https://www.youtube.com/watch?v=6tj8FTdTix0
https://www.youtube.com/watch?v=TQPVS7V3_Jw
https://www.youtube.com/watch?v=x7D1qESYsrA
https://www.youtube.com/watch?v=jhvpuBi0zO4
https://www.youtube.com/watch?v=lbQW_ebiLKA
https://www.youtube.com/watch?v=BlgNhrQPaEA
https://youtu.be/AgPFbaMxf3g


<b>Instructions:</b>

Body: The body has a support on the bottom to become a clean print. The support has to be removed after printing. Infill: 15%

Track: You'll need 64 tracks. Infill: 15%

Pin: There are two different pins. The normal one is 3.7mm. If the chain is to tight, you should print the small one with 3.0mm and add 3-4 of those pins. After printing the pins, you have to remove the small support on each side. Infill: 15%-20%

Small cog: You need 8 small cogs. Infill: 15%

Main cog: You need 4 main cogs. Infill: For the first 10mm you can print it with 15%. For the rest you should use at least 90%.

Rubbertrack: Use Flexifil or Ninjaflex for the rubber track and glue it to the track. The rubber tracks are not necessary but you will love it. Infill: 30%-50%

Track2: If you don't want to print the rubber track or don't have Ninjaflex, you can print track2 instead of track + rubber track. Infill: 15%

Front + back: Print this with brim if it doesn't stick to the surface and use support structure. Infill: 15%

FPV-Cam holder: Print it with support structure and glue the small part on the back side. This is for the servo to move the cam up and down. Infill: 15%

Camera and LED mount: You need these two parts if you want do use a fpv-camera. Infill: 15%

Tow-bar: Infill: 15%

Tow-bar plug: If you don't want to use the tow-bar you need this twice. Infill: 15%

LED-mount: Infill: 15%

Top: The top is designed to use a 40mm fan for cooling the vtx and to plug in the fpv-antenna from banggood. Infill: 15%

Track-body-connector: You can glue the track frame together and glue it to the body but if you do that, you can't replace parts if broken. Use this to mount the track frame to the body. They are marked for front and back. Infill: 15%

Track outer cover: Print this part twice. Infill: 15%

Outer track frame: Print this part twice. Infill: 15%

Inner track frame right/left. Infill: 15%

<b>Parts to print:</b>

1x body (for 2S or 3S)
1x front
1x back
64x track
64x rubber track
64x pins (try which one fits best for you)
8x small cog
4x main cog
1x inner track frame right
1x inner track frame left
2x outer track frame
2x track outer cover
1x top
1x set track-body-connector
1x tow-bar
2x tow-bar plug
1x fpv-cam-holder
1x set camera-led-mount
1x led mount

<b>Parts you need (BOM):</b>

2x package of 10 bearings 688ZZ for the small cog (you need 2 bearings each cog)
https://bit.ly/3F3ZmLg

4x motor with gear (you need 4 motors, 2 for each chain)
http://bit.ly/3Bb6YKQ

2x brushed esc (one esc for each side. connect two motors to one)
https://bit.ly/3ivkvXj

8x bearings 61802 2RS / 6802zz for the main cog (each main cog needs 2 bearings)
http://bit.ly/2wyk0QX

1x Front camera
https://bit.ly/3H8Z60v

1x Rear camera
http://bit.ly/3XGh3Zc (8mm x 8mm or 12mm x 12mm)

1x FPV-switch
http://bit.ly/3uJdCog

1x Package magnets 3mm x 1mm (front and back are sticked to the frame by magnets)
http://bit.ly/3uq9skU

1x fan 40mm (12v) for cooling the vtx
http://bit.ly/3BgRS6H

1x servo for the tilt-mechanism for the cam and LED
https://bit.ly/3VR58Xu

We use 4 tuning motors (Slotdevil 2035) instead of the motors which come with the gear reducer. You can run the tuning motors with 3S (the ESC does supply this, even if they are for 7,4v)

Use 4 motor pinions for the tuning motors (sigma 4 9z m50 nylon)

20x M3 Screw 25mm long https://bit.ly/3izqOcy
4x M4 Screw 20mm long https://bit.ly/3iAtgiW
4x M4 Nuts https://bit.ly/3B7QiE1

FPV-Rover (Tank)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2478547.

This is a mini version of my FPV-Rover V2.0
https://www.thingiverse.com/thing:2952852

The dimension are 10cm x 10cm x 3cm

Intructions and BOM can be found on Instructables
https://www.instructables.com/id/Mini-FPV-Rover/

Videos on Youtube:
https://www.youtube.com/watch?v=mjomPwlsyFQ

<h2>Parts to print </h2>
<ul>
<li>1x body</li>
<li>70x track</li>
<li>70x rubbertrack (only if needed)</li>
<li>1x top</li>
<li>2x inner track frame</li>
<li>2x outer track frame</li>
<li>4x cog</li>
</ul>

Last Update: 28.08.2017
Scroll down for the latest updates

Mini FPV-Rover (Tank)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4708206.

My son wanted some trophies for his slot car track. And it had to be clear, that it's for cars. Therefore I've created a trophy (first, second and third place) with a wheel.

Height is about 10cm.

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Wheel Trophy for (Slot) Car

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5791996.

Use this as replacement for the original one. You need 8 Magnets 4mm x 2mm for the battery the battery cover and front cover. And a hot glue gun.

Battery cover is easy to remove to change the battery. There are two front covers. One with a cut out for an AIO FPV cam and another one without.

BOM
8x 4mm x 2mm Magnet (https://bit.ly/3FpPLQv)
1x AIO FPV Camera (https://bit.ly/3UKnAQV)

FT Mini Arrow Pod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5791663.

This is a remix of the awesome Rugged Box from Whity (https://www.printables.com/model/258431-rugged-box-parameterizable) to store the Revo Nozzles. 
The only things you need are 6 M3 x 30mm screws and 2mm rubber foam sheet, to protect the tip of the nozzles. And of cause Revo nozzles.

BOM:
6x M3x30mm Screw (https://bit.ly/3izqOcy)
1x 2mm rubber foam sheet (http://bit.ly/3Xv8pga)
Revo Nozzle (https://bit.ly/3FOe3m7)

E3D Revo Nozzle Box

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1795583.

This is a 3D-Gimbal for the Black Snapper. It is designed to hold a GoPro Hero3 and to use with small Emax 1806 450kv motors.

As controller board I use the Storm32 controller from banggood. The MPU fits perfect to the backside of the GoPro mount.
I also use a protection lens for the GoPro so that you can add a ND-filter to avoid jello.

There is a hole in arm_2 for the cables. I didn't put the cables through the hole because I tried different arms and didn't want to unplug the cables all the time from the board.

Black Snapper 3D-Gimbal for GoPro Hero3+

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3610232.

This is a remix of the charging dock designed by jsc.

I've splitted the part in two parts (top and bottom) as I wanted to hide the cable on the bottom and it lifted the dock.
In addition I've designed a pad for the bottom to be printed in flex filament (Ninjaflex, TPU) so that the dock doesn't slip on a glass surface.

The two parts are hold together by some 8mmx1mm magnets. The rubber part will be glued to the bottom part.

You need:
six 8mm x 1mm magnets (https://bit.ly/2VDL13R)

No support needed

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Apple Watch Charging Dock

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4730661.

Ever wanted to build your own slot car? Take your bricks like Lego or Bluebrixx and start building.

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Intructions and BOM can be found on Instructables
https://www.instructables.com/Slot-Car-Chassis-for-Bricks/

Videos on Youtube:
https://youtu.be/GtVSWz2-XXg


Parts to print

I've printed all parts in PLA. The slide guide has a build-in support.

1x chassis
1x slide guide mount
4x axle bracket
1x motor mount
1x slide guide


Lego compatible Slotcar chassis for Carrera Go

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1269962.

This is a remix of the rubber bands sentry gun designed by tristomietitoredeituit.
http://www.thingiverse.com/thing:953753

It is the first upgrade for the FPV-Rover (V1.0)
http://www.thingiverse.com/thing:1240754

And for the FPV-Rover (V2.0)
https://www.thingiverse.com/thing:2952852

Videos on Youtube:
https://www.youtube.com/watch?v=K8Hyufccs50

Parts to Print
1x barrel
1x core top
1x core bottom
1x mount
2x fire-servo-support (or 2x fire-servo-support_large)
1x fire wheel (or 1x fire wheel_large)
1x wire guide (or 1x wire guide_large)

BOM
1x servo for the tilt-mechanism
https://bit.ly/3Fqn5a4

1x 360 servo for the fire wheel
https://bit.ly/3VObfMf

2x M5 nuts

1x M5 threaded bar (10cm-15cm)

2x 6mm metal pipe (10cm-15cm)

1x 6mm metal pipe with 5mm hole (5cm)



Rubber Gun for FPV-Rover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1936491.

This is a GoPro-Mount for the FPV-Rover (V1.0)
http://www.thingiverse.com/thing:1240754

And for the FPV-Rover (V2.0)
https://www.thingiverse.com/thing:2952852

GoPro Mount for the FPV-Rover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4630222.

This is the Snow Plow for the FPV-Rover (V1.0)
http://www.thingiverse.com/thing:1240754
And for the FPV-Rover (V2.0)
https://www.thingiverse.com/thing:2952852

Winter is coming. So the FPV Rover needs a Snow Plow to ensure a clean pavement.

Intructions and BOM can be found on Instructables
https://www.instructables.com/Snow-Plow-for-the-FPV-Rover/

Videos on Youtube:
https://www.youtube.com/watch?v=iQ8LBDOw9p8
https://www.youtube.com/watch?v=ULYmqGeH-P4&t=3s

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

<h2>Parts to print</h2>
I've printed all parts from PLA, as nothing is critical on this one. ABS, PETG and all other materials would be fine as well.
<ul>
<li>1x base plate</li>
<li>2x bearing mount</li>
<li>1x body</li>
<li>1x plow left</li>
<li>1x plow right</li>
<li>1x servo arm extension</li>
<li>1x servo pivot</li>
<li>1x servo mount</li>
<li>1x servo arm extension</li>
<li>1x top mount</li>
</ul>

Snow Plow for FPV Rover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3835285.

This is the Nerf Dart Launcher for the FPV-Rover (V1.0)
http://www.thingiverse.com/thing:1240754
And for the FPV-Rover (V2.0)
https://www.thingiverse.com/thing:2952852

From the beginning of building the FPV-Rover, I wanted to have a Nerf Dart Launcher on it.
And finally, here it is. This is the fifth upgrade for the rover and it won't be the last.

Intructions and BOM can be found on Instructables
https://www.instructables.com/id/Nerf-Darf-Launcher-for-the-FPV-Rover

Videos:
https://youtu.be/AgPFbaMxf3g 

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/


<h2>Parts to print</h2>
I've printed all parts from PLA, as nothing is critical on this one. ABS, PETG and all other materials would be fine as well.
<ul>
<li>1x servo cover</li>
<li>1x battery cover (with or without cutout)</li>
<li>1x dart feeder</li>
<li>1x esc bracket</li>
<li>1x armoured conduit</li>
<li>2x dart launcher</li>
<li>1x base plate</li>
<li>1x top plate</li>
<li>1x servo arm extension</li>
<li>1x nerf dart storage</li>
<li>1x top cover</li>
<li>1x 18650 battery pack (if you want to use 18650 batteries like I do)</li>
</ul>

Nerf Dart Launcher for the FPV-Rover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4719170.

Why not combine two hobbies, FPV and slot car.

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Intructions and BOM can be found on Instructables
https://www.instructables.com/FPV-in-a-Slot-Car/

Videos on Youtube:
https://youtu.be/ozkBXrVjpBc

<h2>Parts to print</h2>
I've printed all parts from PLA. No Support needed. The slide guide has a build-in support.
<ul>
<li>1x chassis</li>
<li>1x slide guide mount</li>
<li>4x axle bracket</li>
<li>1x motor mount</li>
<li>1x slide guide</li>
<li>1x main body</li>
<li>1x front body</li>
</ul>

Carrera GO FPV in a Slot Car

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4711276.

What do you do with your coins if you have too many and the wallet gets bigger and bigger? Just throw them into the coin collector and store them there. 
And if you need spare money, open the collector and take whatever you need.

Hole diameter is 30mm
Total height is 70mm
Height of the collector box 50mm

You need 4x magnets 6x3mm (https://bit.ly/3F0y1d8) to attach the top to the bottom.

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Coin Collector Box

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5790478.

This is a remix of the puzzle box by Scorch.
The box was designed for a nickel and as it is very hard to find one in Europe, I've remodeled it to fit an Euro.

I've redesigned the holes and gaps, as it was a little too wobbly.

You need

1x M4x25mm screw (https://bit.ly/3F3V3jc)

1x M4 nut (Lock nut) (https://bit.ly/3voxc9I)

1x 7mm ball/pearl (http://bit.ly/3QF3MOn)

Coin Puzzle Box

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2901247.

This is a nightlight to have it not so dark in our son's room.

Print all parts once and use support where needed (moon, base plate, lid).
Use natural/transparent filament (at least for the moon) .

Glue the moon to the base plate. The lid can be screwed to the base plate if needed.

Find the moon here and scale it to 125%
https://www.myminifactory.com/object/3d-print-moon-bunny-60705

Find the bunny here and scale it to 125%
https://www.myminifactory.com/object/3d-print-60081

I used these LED fairy string to lighten the moon.
https://goo.gl/quymBJ

Moon bunny as nightlight

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3511731.

This is a printable LED lamp with WS2812 LEDs. They can be powered via USB, power supply or with an Arduino.

Intructions and BOM can be found on Instructables
https://www.instructables.com/id/Printable-LED-Lamp

Follow me on Instagram for latest news
​https://www.instagram.com/ernie_meets_bert/

Printable LED Lamp

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2218727.

This is a remix of the Micro SD Card Holder.

I've added space for an USB-C adapter for the micro SD cards.
https://goo.gl/pbKReZ

The second  bottom part is for a normal USB adapter.
https://goo.gl/uwaVDe

Micro SD Card holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1479824.

Replacement for the original Black Snapper landing gear

Black Snapper landing gear

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Markus_P

Achievements

Seedling

Debutant