Maple 3D Printing3.8K followers

Window Pikachu - Pokemon

1.4K downloads · 6 months ago · Membership Exclusive model as part of my Thangs or Patreon Memberships Minor Supports needed painte

Description

Membership Exclusive model as part of my Thangs or Patreon Memberships

Minor Supports needed painted 3mf included Split model for full color print

www.maple3dprinting.com

Tags:

Community Makes (12)

I recorded the make into a YouTube short:
https://youtube.com/shorts/PYUggpgzvyk

Cute little window display, the added sparkle from the Prusament PLA (Prusa Galaxy Black and Galaxy Red) adds a nice little touch for the Electric type Pokemon!

The design is very nice and with my previous post I was able to slightly reduce the overhang by increasing the fan, decreasing the speed on the outer wall and the temperature, increasing its thickness to 0.45 mm.

I have had some problems in certain areas, especially on overhangs and supports.

Has anyone had better results and could advise me?

I have already tried several parameters on the supports and increasing the fan speed and also lowering the printing speed.

And it begins!! Tweaked a couple settings to dial this bad boy to my liking

Printed on the H2C in one piece in 5 colors. Scaled size to my liking.
Love be these window models they are so cute and fun.

I absolutely love the model, however would you have any suggestions for best way to avoid the yellow being somewhat "see-through" as you can see in my photos. This is 100% an issue on my side as opposed to the design, I know there are some settings I can tweak like wall loops, but thought I'd ask here before changing anything and trying again.

This was scaled down significantly to fit inside of a PC tower case :)

I hope you do more of the adorable window guys!!! <3 I just shared my 1 print on TIKTOK :) I'm going to print all 5 of them you have for my front window :)

Was told to do window Pikachu so I did !

Now he gets to sit right next to charmander.

Be careful with the very small nose and eyes, those are tricky.

Community Makes (12)

Discussions

Trevor3DPrints3 months ago

Printed on the H2C in one piece in 5 colors. Scaled size to my liking. Love be these window models they are so cute and fun.

MaterialPLA

brandonrwigginton5 months ago

Was told to do window Pikachu so I did ! Now he gets to sit right next to charmander. Be careful with the very small nose and eyes, those are tricky.

PrinterAnycubic Kobra S1

MaterialPLA

Layer height0.12 mm

Infill density5 %

SupportsTree

DawnStar Stamping22 days ago

PrinterOther

Printer modelSnapmaker U1

MaterialPLA+

maik.thiel172 months ago

All good ;)!

MaterialPLA

Layer height0.2 mm

SupportsTree

BrimNo

MulticolorMultiple Hotends

donellelaws3 months ago

I hope you do more of the adorable window guys!!! <3 I just shared my 1 print on TIKTOK :) I'm going to print all 5 of them you have for my front window :)

PrinterBambu Lab H2D

MaterialPLA

lewmarday223 months ago

THIS TURNED OUT SICK!!

PrinterBambu Lab A1

MaterialPLA+

Layer height1.6 mm

Infill density5 %

SupportsTree

gz.3dart28 days ago

Amazing models! any version you provided went out clean from the printer i tried to replicate the "real size" (41cm Height) by slicing it in half, i just need to figure it out how to remove the problem between the ear (but that' just why i'm playing with the model). Great Job!

PrinterBambu Lab A1

MaterialPETG

Layer height0.2 mm

Infill density15 %

SupportsTree

Crisendo2 months ago

I recorded the make into a YouTube short: https://youtube.com/shorts/PYUggpgzvyk Cute little window display, the added sparkle from the Prusament PLA (Prusa Galaxy Black and Galaxy Red) adds a nice little touch for the Electric type Pokemon!

PrinterPrusa XL

MaterialPLA

SupportsTree - Manual

Material BrandsPrusament PLA and OVERTURE PLA

tlachiditodg3 months ago

The design is very nice and with my previous post I was able to slightly reduce the overhang by increasing the fan, decreasing the speed on the outer wall and the temperature, increasing its thickness to 0.45 mm.