This is a full set for a complete overhaul for an Ender 3. Say 'Begone' to the horrific factory cable management, for a simple, yet elegant solution.

Features 3 parts, a hotted mount (suitable for Petsfang 5015 fan shrouds), a top mount, and a guide piece.

**Hardware parts**
M5 longish bolt * 1
cable ties
m6 pneumatic coupling for 4mm OD PTFE
12mm pneumatic coupling for 4mm OD PTFE
4mm OD PTFE (a few metres, can be cheap stuff)

Ender 3 cable management overhaul

HotendCableMount.3mf

For updates, view the Printables page https://www.printables.com/model/201511-ender-3prov2-purge-bucket

This is the culmination of months of rigours testing.

This part mounts to the front of the bed on and Ender 3 3D Printer (tested on an Ender 3 Pro) via the bed screw mounts.

**Components needed**

Silicon pastry brush (I sourced mine from [Woolworths Australia](https://www.woolworths.com.au/shop/productdetails/521878/essentials-pastry-brush-assorted))
M4 nuts * 4
3D printed Ender 3(pro/v2) tool tray
Part

**Installation instructions**

1. Install the tool tray according to its instructions
2. Remove the heated bed, being careful to stow all the screws
3. Remove glass from the top of the bed
4. Attach nuts to the bolts protruding from the bed on the front left, and both back bolts. Tighten them.
5. Place the part on the final, exposed screw with the nut trapped inside
6. Tighten
7. Cut the brush part off the pastry brush
8. Gently push in the pastry brush bristles into the holder, being careful not to snap it
9. Reassemble the 3D printer
10. 

**Gcode tuning**

Attached below is a link to my tool change script compatible with PrusaSlicer, and SuperSlicer. You will need to tune all of the values to suit your specific machine.

[Toolchange script](https://zerobin.net/?b67b5e871c96693f#Co+3Q53HR/0whN7umENIKP67g/YYYV9+xa4jYO+4aE0=)
[Start script](https://zerobin.net/?9c26320f6c840eec#2arvBmFHdkqWLWRghAzNGejNCC/5MooYnEQVIerUNDo=)

**Hardware tuning**
You will have to move your endatops slightly, in my case just a bolt used for sensorless homing.

**Print settings**
Material: ABS (clear)
Supports: Yes, build plate only

**DISCLAIMER**
I AM NOT RESPONSIBLE FOR ANY DAMAGE THIS MAY CAUSE. THIS MODEL IS SUPPLIED 'AS IS' AND WITH NO WARRANTY WHATSOEVER. USE AT YOUR OWN RISC!!!

Ender 3 dual extrusion purge bucket

This is the culmination of months of rigours testing.

This part mounts to the front of the bed on and Ender 3 3D Printer (tested on an Ender 3 Pro) via the bed screw mounts.

**Components needed**

Silicon pastry brush (I sourced mine from [Woolworths Australia](https://www.woolworths.com.au/shop/productdetails/521878/essentials-pastry-brush-assorted))
M4 nuts * 4
3D printed Ender 3(pro/v2) tool tray
Part

**Installation instructions**

1. Install the tool tray according to its instructions
2. Remove the heated bed, being careful to stow all the screws
3. Remove glass from the top of the bed
4. Attach nuts to the bolts protruding from the bed on the front left, and both back bolts. Tighten them.
5. Place the part on the final, exposed screw with the nut trapped inside
6. Tighten
7. Cut the brush part off the pastry brush
8. Gently push in the pastry brush bristles into the holder, being careful not to snap it
9. Reassemble the 3D printer
10. 

**Gcode tuning**

Attached below is a link to my tool change script compatible with PrusaSlicer, and SuperSlicer. You will need to tune all of the values to suit your specific machine.

[Toolchange script](https://zerobin.net/?b67b5e871c96693f#Co+3Q53HR/0whN7umENIKP67g/YYYV9+xa4jYO+4aE0=)
[Start script](https://zerobin.net/?9c26320f6c840eec#2arvBmFHdkqWLWRghAzNGejNCC/5MooYnEQVIerUNDo=)

**Hardware tuning**
You will have to move your endatops slightly, in my case just a bolt used for sensorless homing.

**DISCLAIMER**
I AM NOT RESPONSIBLE FOR ANY DAMAGE THIS MAY CAUSE. THIS MODEL IS SUPPLIED 'AS IS' AND WITH NO WARRANTY WHATSOEVER. USE AT YOUR OWN RISC!!!

This is a 3D printable mechanism that utilises a standard microswitch, a cable tie, two m5 bolts, two m5 nuts, and a piece of string.

The string is connected to the end of the switch with a cable tie. When the lifter is stowed, the string is wrapped around the shield, and as it lifts up it unravels. This was used for FRC (first robotics team) [5985](https://www.thebluealliance.com/team/5985). This was used to detect when a climber had reached end of travel as an emergency stop procedure. Be aware that if the switch is not reset properly, it will remain tripped and the climber will not deploy.

Vertical Lifter Limit switch

switchMount.3mf

This mount takes a Limelight 2/2+ and 2 servos and creates a robust pan/tilt mount for use with FRC Vision tracking. 

**Printed parts required**
4 * spacer
1 * all other parts

**Other hardware**
2 * servo
2 * round servo horn
Double sided tape
M3 bolts

**Assembly**

All parts either bolt together or in the case of the servo horns, they are either attached with double sided tape or small self tapping screws.

Limelight 2(+) Pan Tilt mount

panbase.3mf

This is a simple dock for 3.5/2.5" SATA drives. It utilises a SATA USB interface pulled out of a [Segate 4tb expansion drive](https://www.amazon.com.au/Seagate-Expansion-Desktop-External-STEB4000100/dp/B00TKFEE8K) (purchased at Officeworks AU). The board was attached via double sided tape to the dock, after a drive was inserted to get proper spacing. It then just took 4 generic rubber feet, and a few longish M3 bolts to secure the top to bottom.

HDD Dock for SATA drives

side.3mf

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4287316.

This is a simple bed level test part that can be printed with dual extrusion. This also will serve as an offset calibration test. 

Ender 3 bed level test (dual extrusion) / offset calibration

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4589386.

This is a super simple bracket to adapt the stock display mount on a Ender 3 or similar machine. It should take at most 3hrs and ~15g to print, so is very simple. 

This design is not perfect. STEP file is included incase you want to modify it easily. 

V2.1

MKS TFT32 Display adaptor Ender3, 5, clones, ect.)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3939752.

Have you ever had that time, when you have to work on your Hotend, but the extrusion keeps going down? Trying to insert your Bowden tube, but every time you put any force on your Hotend, it just descends. This problem stops now! This simple brace, stops it from going down while you are working on it. You can easily lengthen it as well!

Render done in Fusion360: Ender 3 model: https://github.com/Creality3DPrinting/Ender-3/tree/master/Ender-3%20Mechanical/F360 .

Version 1.0.1

2020 Extrusion Support

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3907247.

The main point of this remix, is to provide a stand for a Ford ST badge designed by LAMcDonald. It can display it on a shelf for maximum effect. Print 2, one for your keyring, and one for your stand. CAUTION: the ring part of it has been prone to snapping, so printing with 100% infilled is a requirement.

Ford Focus ST Badge (+ Stand)

STLogoKeyring006.stl

Dual extrusion version

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3905741.

This mount is a bracket for a Limelight machine vision camera that can be tilted and adjusted to find the correct angle. Just put 2 M3 screws through the holes and fasten with star washers between them. This locks it in place. Be careful, as under high stress, it can crack. Fasten the limelight with 4 cable ties.

Version 2.0.0


Limelight Tilt mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3905697.

This stand is designed to hold an Apple Watch and wireless charger in nightstand mode (shows clock face like bedside clock) and protects the case and band from damage.

Version 1.1.0

Apple Watch Magnetic Charging Stand

Stand.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3901993.

This is a mount for a Nema 17 stepper motor for an extruder for any printer with a 2020 extrusion. It mounts up the top next to the spool and uses 2 bolts and square/t-nuts. It does require an extended cable. This helps to improve the filament path on machines like the Ender 3, as it can reduce flow. You may need a longer PTFE tube.

The cutout for the Stepper: https://www.thingiverse.com/thing:83340

Version 0.9.0

Extruder mount for Creality Machines (improved filament path, supports dual extrusion)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4554001.

This is a remixed extruder mount that supports common 'sandwich mount' style extruders, such as the E3D Titan. Secured with a M3 screw. If it is not secure enough, use a Tee nut (I have found a way to make a tee nut with a M3 nut, M3 washer, M5 fibre washer (sides trimmed), extrusion slot, bracket, bolt stack).

2020 Extruder motor bracket

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

LordBBQ

Achievements

Seedling

Debutant