It consists of two pieces. The dock and the lid.

Your original Nintendo switch and dock drop perfectly into a slot at the back of the new upgraded dock. (Only tested with OLED version, but it should work with the original as well; it just might not be a perfect fit.)

Then there is a compartment at the front of the new upgraded dock that holds two extra joycons, four joycon straps, and up to six game cartridges.

All the accessories have perfect cutouts, so everything slides right into place and doesn't move.

The lid is also magnetic, so it stays in place as well.

Their are three versions (As seem in my YouTube video), cut panels, full panels and wide panels. The wide panels version.

**PRINT SETTINGS:**

These are very straightforward prints.

The dock and the lid have spots to embed magnets.  **I HIGHLY RECOMMEND USING A DROP OF SUPER GLUE WHEN INSTALLING THE MAGNETS, SO THEY DON'T POP OUT WHEN THE PRINT HEAD GOES OVER THEM.**

You will need 4, 6 by 3mm Neodymium Magnets. These are the magnets I use if you are interested:

60 Pack on Amazon: https://amzn.to/47pQFaj

100 Pack on Amazon: https://amzn.to/3Sa8beg

**Also, if you would like to see how I designed these docks, you can find them on my YouTube channel. Just hit the join button.**

Cheers,

Kevin

Disclaimer: Some links in this description may be affiliate links. This means I may earn a small commission if you click them and make a purchase. It's no extra cost to you, but it truly helps me to keep producing free designs. Thank you!



Modern OLED Nintendo Switch Dock (Organizer) - Wide Panels

Nintendo Switch Dock (Wide Panels) .3mf

It consists of two pieces. The dock and the lid.

Your original Nintendo switch and dock drop perfectly into a slot at the back of the new upgraded dock. (Only tested with OLED version, but it should work with the original as well; it just might not be a perfect fit.)

Then there is a compartment at the front of the new upgraded dock that holds two extra joycons, four joycon straps, and up to six game cartridges.

All the accessories have perfect cutouts, so everything slides right into place and doesn't move.

The lid is also magnetic, so it stays in place as well.

Their are three versions (As seem in my YouTube video), cut panels, full panels and wide panels. The cut panels version.

**PRINT SETTINGS:**

These are very straightforward prints.

The dock and the lid have spots to embed magnets.  **I HIGHLY RECOMMEND USING A DROP OF SUPER GLUE WHEN INSTALLING THE MAGNETS, SO THEY DON'T POP OUT WHEN THE PRINT HEAD GOES OVER THEM.**

You will need 4, 6 by 3mm Neodymium Magnets. These are the magnets I use if you are interested:

60 Pack on Amazon: https://amzn.to/47pQFaj

100 Pack on Amazon: https://amzn.to/3Sa8beg

**Also, if you would like to see how I designed these docks, you can find them on my YouTube channel. Just hit the join button.**

Cheers,

Kevin

Disclaimer: Some links in this description may be affiliate links. This means I may earn a small commission if you click them and make a purchase. It's no extra cost to you, but it truly helps me to keep producing free designs. Thank you!



Modern OLED Nintendo Switch Dock (Organizer) - Cut Panels

Nintendo Switch Dock (Cut Panels) .3mf

It consists of two pieces. The dock and the lid.

 

Your original Nintendo switch and dock drop perfectly into a slot at the back of the new upgraded dock. **(Only tested with OLED version, but it should work with the original as well; it just might not be a perfect fit.)**

 

Then there is a compartment at the front of the new upgraded dock that holds two extra joycons, four joycon straps, and up to six game cartridges.

 

All the accessories have perfect cutouts, so everything slides right into place and doesn't move.

The lid is also magnetic, so it stays in place as well.

 

Their are three versions (As seem in my YouTube video), cut panels, full panels and wide panels. The full panel version is free to download and if you would like to pick up the other designs or just support my work, you can download them on thangs.

 

**PRINT SETTINGS:**

 

These are very straightforward prints.

 

The dock and the lid have spots to embed magnets.  **I HIGHLY RECOMMEND USING A DROP OF SUPER GLUE WHEN INSTALLING THE MAGNETS, SO THEY DON'T POP OUT WHEN THE PRINT HEAD GOES OVER THEM.**
 

You will need 4, 6 by 3mm Neodymium Magnets. These are the magnets I use if you are interested:

 

60 Pack on Amazon: https://amzn.to/47pQFaj

100 Pack on Amazon: https://amzn.to/3Sa8beg

 

**Also, if you would like to see how I designed these docks you can find them on my YouTube channel. Just hit the join button.**

 

Cheers,

Kevin

 

Disclaimer: Some links in this description may be affiliate links. This means I may earn a small commission if you click them and make a purchase. It's no extra cost to you, but it truly helps me to keep producing free designs. Thank you!

Modern OLED Nintendo Switch Dock (Organizer) - Full Panels

Nintendo Switch Dock Panels .3mf

This is the second sound amplifier I've made (well, technically the second and third). There are two versions. Both are modern style phone stands, but they have a cutout for your phone speaker and are hollow on the inside.

The side speaker version (green one) like the name suggests, has openings on the side for the sound to come out.

The front speaker version (white one) has perforated holes on the front, so the sound travels out forward. This version is slightly larger than the side speaker version to accommodate the speakers being on the front.

These speakers aren't as loud as the spiral sound amplifier I made, but they are definitely more compact.

Print Setting:

These are very easy to print.

They print on there sides without supports.

A 3MF file will also be linked down below for easy printing.

Front & Side Speaker Phone Stand

(Front Speaker) Phone Stand.3mf

Just like the other two business card holders, I thought this would look cool on a desk as well. (Hopefully its not just me who likes it lol).

Its extremely easy to print and it's just one piece. It holds the cards up at about a 60 degree angle with a max capacity of about 15 cards.

Its more of a form-over function piece, but it still works well. (Just be careful when pulling cards out because it can tip over.)

Modern Minimalist Business Card Holder

Minimal Card Holder .stp

For some reason, I was inspired to make business card holders this month. They are both shaped like a fire, which I thought would look pretty cool on a desk.

The "tinder" fire holder is 3 pieces that are just superglued together.

I also included a 3MF file for the "tinder" holder that is multicolor for people with an AMS but if you don't have an AMS, you can simply add a stop and change filaments.

Supports Needed?

Yes

Tinder Business Card Holder 

Tinder Card Holder (Multipart, Multicolor).3mf

 It is shaped like a rose, and it fits in the palm of your hand. It's print in place and has holes for magnets to keep it securely closed. It also has a cut-out for a ring on the inside, and the neat part is that it will fit a wide variety of ring sizes without them falling out.

 The ring will stay in place because of a separate spring that pushes against the ring to keep it from moving around. -This spring is printed separately and needs to be inserted mid-print (I've included a stop for it in the 3MF file, along with stops for the magnets). *see photo for more details

You will need 16, 6 by 3mm Neodymium Magnets. These are the magnets I use if you are interested:

 60 Pack on Amazon: https://amzn.to/47pQFaj

100 Pack on Amazon: https://amzn.to/3Sa8beg

 Have a great Valentine's Day!

Sincerely,

Kevin

 Disclaimer: Some links in this description may be affiliate links. This means I may earn a small commission if you click them and make a purchase. It's no extra cost to you, but it truly helps me to keep producing free designs. Thank you!

Rose Ring Box 

Rose Ring Box OP (1).3mf

❤️  Set the mood with your significant other with this heart-shaped wine holder. The wine holder comes in a smooth, flat design and a rose-patterned design.

There are four files, two are for 75mm bottles, which is a common small wine bottle size and the other two files are for bottles ranging from 75mm to 90mm (if your wine bottles vary in size or if you buy champagne, then I would print the larger version). The twisted heart rings are a tabletop decorative piece, but they are kind of fun to play with too. 

**Print Settings**
The flat wine bottle holder design prints best upright, and the rose design needs to be printed on its side. 

Heart Shaped Wine Bottle Holder

Rose Heart Wine Holder (Small 75mm Bottle Size).stl

❤️  Set the mood with your significant other with these twisted heart rings! 

The twisted heart rings are a tabletop decorative piece, but they are kind of fun to play with too. 

*NOTE - The twisted heart rings are extremely hard to print, I've done my best to make it as easy as possible to print with the 3MF file, but its not perfect. They are much better suited for a resin printer, in my opinion but if you know how to print it better than me, I would be extremely grateful if you let me know! 🙏

Twisted Hearts

Twisted Hearts G3MF.3mf

💣 This one will definitely be a fan favorite with kids and adults! I wanted to create a grenade toy that exploded when it hit something. After a lot of thought, I decided to design it using magnets (16 in total).

I first created the grenade, and then I broke it into pieces like a puzzle. After that, I added the holes for the magnets, and now we have a functioning toy grenade!  It is quite fun to use, and I'm excited for you to try it out! Keep in mind that it's very easy to lose the pieces because they go flying everywhere, but its worth it lol.

I made five files that make up the grenade. The bottom section, middle piece, top section, handle, and pin.

I didn't put all of them on the same build plate to make keeping track of the magnets direction (polarity) easier. 

**Print Setting:**
- **I highly reccomend using super glue when installing the magnets. (To prevent them from flying out and sticking to the print head)**

I recommend printing the bottom pieces first, then moving to the middle piece, then the top pieces, followed by the handle and the pin. I will have 3MF files for each piece with all the settings I used to print them (including the stops needed to embed the magnets into the print. **(Double check this before printing)**



I recommend 30% infill or less. If you do more infill, the magnets might not be strong enough to stick to each other.

You will need 16, 6 by 3mm Neodymium Magnets. These are the magnets I use if you are interested:

60 Pack on Amazon: https://amzn.to/47pQFaj

100 Pack on Amazon: https://amzn.to/3Sa8beg

If you don't know how to orientate the magnets please message me and I will put a video together if needed. 

You can also purchase key rings to attach to the pins here: 

https://amzn.to/3tSN6f4

Scalability

I would not scale it up but you might be able to scale it down a little bit.

Supports Needed?

No 

Thank you for the support! More designs are on the way and if this design is a hit, I will most likely make some variations. 

Happy Printing!

Cheers,

Kevin

Blast Grenade.3mf

This is the fourth and last articulating flower I'm going to make for now (unless I get more requests). The shape resembles a columbine flower; it is a simple design, but I thought it still looked nice.  Just like the previous coasters I made, this can bend and flex in both directions. They are also print in place and big enough to hold most cups and cans.

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

Scalability

Can be scaled up and down a bit.

Supports Needed?

No (but if you have trouble with the links in between the flower petals, I recommend slowing the print speed down). Also, please let me know if you run into any issues printing these. Thank you.

Thank you for the support, and I'm on to different designs moving forward. If you have any suggestions, I would love to hear from you! Happy Printing!

Cheers,

Kevin

Sunflower Coaster (Articulating)

Sunflower Coaster F...stp

This is my second articulating flower coaster. It resembles a peacock tail pattern, which I thought looked kind of cool. Just like the last coaster I made, these can bend and flex in both directions. They are also print in place and big enough to hold most cups and cans.

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

Scalability

Can be scaled up and down a bit.

Supports Needed?

No (but if you have trouble with the links in between the flower petals, I recommend slowing the print speed down). Also, please let me know if you run into any issues printing these. Thank you.

Thank you for the support, and keep your eyes peeled for the last coaster in the coming days! Happy Printing!

Cheers,

Kevin

Eye Flower Coaster (Articulating)

Eye Flower Coaster..stl

How hard could it be to stack these? I'll let you find out, lol.😅 This five-piece rock block set is fun to try and stack when you are bored and is a great test of patience.  If you have children, they may be tempted to play with these; just watch out when they get frustrated and throw them at you! (I'm making a version that has more texture and grip, which will be much more enjoyable for children and adults.)

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

I printed these with 10% infill. Using more infill should make the blocks stack easier because they are heavy, but don't quote me on that. 

Scalability

These blocks can be scaled up or down.

Supports Needed?

No

Again, thank you for the support, and I hope you have a good time stacking these blocks! Happy Printing!

Sincerely,

Kevin

Impossible Stacking Blocks

Impossible Stacking Blocks...stp

Is it a chicken or an egg? I guess it's both 😅. This was a fun design for me. After many test prints, it finally came together nicely. It prints in two pieces that are hollowed out, so you can store stuff inside. Both pieces screw together perfectly, so your chicken egg won't fall apart.

PRINT SETTINGS:

Supports: Yes, use one tree support for the underside of the chicken top piece.  

Seam Position: Back (So it's not going through the face) 

.2mm layer height

*Variable layer height makes smoother curved prints, but it is not necessary for this print.

Tested with PLA only. 

PRINT DIMENSIONS:

The chicken egg container is 67mm x 67mm x 82mm 

WATCH THE VIDEO & FOLLOW ME AT:

[https://www.youtube.com/@kevbot.](url)

Chicken Egg Container

Egg Container .stl

I've always been fascinated by sound, music, and frequency. So making a phone sound amplifier was high on my list of things to do. After many prototypes, I came up with a design that works fantastic and is hopefully easy to print. 

Shaped after a spiral shell, this little speaker will seriously boost the volume of your phone speaker! Not to mention, it doesn't require any electricity. It would be a great item to bring with you on a camping trip. 

I designed it to be wide enough to fit most phones, with generous space from side to side. The cutout in the shell is also big enough to capture the sound from most phone speakers. So fitment shouldn't be a problem for most people, and I can always make variations if I receive feedback that it's not the right size.

This is a fun item to print and show friends when they come over! Try it out, and let me know what you think! 

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

Use 3 Walls.

Scalability

Can be scaled up and down a bit. Be careful when scaling down, because your phone might not fit in the holder.

Supports Needed?

Yes, on the build-plate only.

** If your printer does not have good cooling, I recommend painting supports underneath the large opening where the sound comes out. A few strands of filament can sag down if you don't add supports.

- I will include a 3ML file with all the proper settings so you can easily print. 

** If you have a machine like the X1C, you should be able to print this with only supports on the build plate. 

Further Printing Notes: 

If you are having trouble with the bottom rounded portion of the print, try using  variable layer height to smooth out the print. 

Thank you again for all the support, and I hope you love the speaker! Let me know if you would like to see any other speaker designs! Happy Printing!

Sincerely,

Kevin

Spiral Sound Amplifier

Spiral Sound Amplifier.stl

When your friends visit, they'll be impressed with this coaster 😀.

Shaped like a beautiful flower, with links between each petal. This flower coaster can bend and flex a bit, making it a unique table piece. It's print in place and is big enough to hold most cup and cans. 

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

Scalability

Can be scaled up and down a bit.

Supports Needed?

No

Thank again for all the support, and I hope you love the Coaster! Let me know if you would like to see any other coaster designs! Happy Printing!

Sincerely,

Kevin

Articulating Flower Coaster 

Flower Coaster (1).stl

Watch out! This little guy is very spiky and can bite! 🐊

The goal of this design was to make an aesthetically pleasing crocodile clip that was print in place and also functional, which I believe was achieved 😎. The clip is mainly just for amusement but may have some practical applications. 

Printing Description / Settings

Tested with PLA; not tested with any other filaments.

Scalability

This croc can be scaled up or down.

Supports Needed?

No

Grumpy Crocodile Clip

Grumpy Croc Clip.stl

**EXCLUSIVE KEVBOT CONTENT**

**UNLIMITED DOWNLOADS**
- Each month, you'll be able to choose as many models as you please from my large collection of models, all available in the Exclusive Kevbot Library. 

**COMMERCIAL LICENSE**
- Also make money selling your prints with a **commercial license. **

Partner

**EXCLUSIVE KEVBOT CONTENT**

**12 DOWNLOADS**
- Each month, you'll be able to choose **up to 6 items** from my large collection of models, all available in the Exclusive Kevbot Library. 

**COMMERCIAL LICENSE**
- Also make money selling your prints with a **commercial license. **

Maker

**EXCLUSIVE KEVBOT CONTENT**

**6 DOWNLOADS**
- Each month, you'll be able to choose **up to 6 items** from my large collection of models, all available in the Exclusive Kevbot Library. 

**COMMERCIAL LICENSE**
- Also make money selling your prints with a **commercial license. **


Supporter

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Kevbot.

Achievements

Explorer

Seedling

Fan Favorite

Pinned models

Grumpy Crocodile Clip

Articulating Flower Coaster

Spiral Sound Amplifier

Blast Grenade.3mf

Modern OLED Nintendo Switch Dock (Organizer) - Wide Panels

Modern OLED Nintendo Switch Dock (Organizer) - Cut Panels

Modern OLED Nintendo Switch Dock (Organizer) - Full Panels

Front & Side Speaker Phone Stand

Modern Minimalist Business Card Holder

Tinder Business Card Holder

Rose Ring Box

Heart Shaped Wine Bottle Holder

Twisted Hearts

Blast Grenade.3mf

Sunflower Coaster (Articulating)

Eye Flower Coaster (Articulating)

Impossible Stacking Blocks

Chicken Egg Container

Spiral Sound Amplifier

Articulating Flower Coaster

Grumpy Crocodile Clip