These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This is a jellyfish air plant holder, it was originally designed to be printed with SLA but I can be printed with FDM by using support.  

It is ~95 x 50 mm with a 1 mm hole to accommodate some fishing line.

Jellyfish air plant holder

This is a jellyfish air plant holder, it was originally designed to be printed with SLA but I can be printed with FDM by using support.  

It is ~95 x 50 mm with a 1 mm hole to accommodate some fishing line.

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This is the a rotating, tank shaped plant pot that makes plants look like tiny explosions!

It features a keyed coupling of the turret and base. The plant area is a 22 x 33 mm cylinder so size your plants or prints accordingly.


Tankpot: tank shaped plant pot

Tankpot top

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This cup holder is specifically designed to fit a standard 1L Nalgene water bottle and an M8 hex bolt.

It mounts directly to an inflatable paddle board’s "action cam" mount but it should work on any M8 thread.

Nalgene bottle SUP cup holder

nalgene base

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This sliding lens cap is designed for the Sony FDR-X3000 action camera underwater housing.

It has a spring retention mechanism that keeps the lens cap in place. I have uploaded two versions: one with and without a loop.

Sony X3000 action camera lens cap

X3000_lenscap_w_loop_KaziToad.stl

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This pistol grip is designed for the Sony FDR-X3000 underwater housing (maybe other models as well) .

The "thumb screw" is designed to fit around a standard 0.5 in. long 1/4" x 20 hex bolt and secures the grip to the bottom of the camera.

I suggest printing with 100% infill for rigidity and to limit the amount of water that can penetrate the grip.

Sony X3000 action camera grip

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This is a simple Christmas tree designed to be printed in vase mode. It should be printed without support, 3 floors and only a single spiral wall. 

It only took 25 min and 13g to print this using an 0.8mm nozzle, 0.4mm layer height and 0.8mm line width. 

Check out my realistic tree [here](https://thangs.com/designer/Kazi%20Toad/3d-model/Tealight%20Christmas%20tree-513386?manualModelView=true).

Vase Mode Christmas tree

This is a simple Christmas tree designed to be printed in vase mode. It should be printed without support and only a single spiral wall. 

It only took 25 min and 13g to print this using an 0.8mm nozzle, 0.4mm layer height and 0.8mm line width. 

Christmas tree with ornaments

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This model is just in time for Halloween. 

It is a ghost jack-o-lantern that shows its face when lit from underneath.  It has just enough room to fit an electric tea light (no real fire please).

It can print without support if you can handle some bridging. 

Enjoy :)

Ghost Pumpkin with Hidden Face

This model is just in time for Halloween. 

It is a pumpkin ghost that shows it's face when light from underneath.  It has just enough room to fit an electric tea light (no real fire please).

It can print without support if your printer can handle some bridging. 

Enjoy :)

Pumpkin_Ghost_with_Hidden_Face_KaziToad.stl

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

These mounts are designed to use standard yellow dot (or double yellow dot) squash balls to act as dampening feet for your 3d printer. 

They can be used on any machine that uses a 4040 aluminum extrusion (such as the Ender series) . Each foot needs 4x M4 x 10mm bolts, 4x M4 anchors and 1x squash ball. 

There are also two models ("back right" and "back left") that are specifically designed for the Ender 3 V2. These two account for the power supply flange and screw heads that would otherwise be in the way. 

They should be printed flat side down, the regular feet should be printed without support but the modified ones need a bit. 

Squash ball feet for 4040 Al extrusion (Ender 3 V2)

regular_4040_squashball_foot_KaziToad.stl

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Don't you hate misplacing your individual SD cards? Well now you can lose all of them at once with this tiny SD card case :)

This case features a geared hinge that provides a super smooth opening and is designed to snap into place to avoid using external components. The best part is you don't need support! Just orient the "case" with the gears pointed up and the "base" with the openings pointed up.

I am providing 4 different case models: two "4x" that hold 4 full sized SD cards (with and without magnets) and two "mixed" that hold 2 full sized SD cards and 4 micro SD cards (with and without magnets).

I suggest you print the versions with magnets. They provide the right amount of force to keep your memory cards secure and give a satisfying 'snap' that I can't stop playing with.

Printing:

For one complete card case print 2x "case" and 1x "base" of the same version. Do not use the "4x" base with the "mixed" case.

The "mag" versions are designed for 2 x 5 mm cylindrical magnets (super cheap on Aliexpress). It is a good idea to use a 2 mm drill bit (by hand) to clean the holes before super gluing the magnets in place.

Before assembly make sure the gears and hinge pins are clean (no zits or blobs). To assemble, place the two "case" parts together and pop in the "base" piece (use a C-clamp if needed). 

I suggest printing in PLA at a 0.15 mm layer height or lower, 10% infill, no support, at least 3 walls, and 5 roof/floors.


Geared SD Card Case

4x_SDcard_case_mag_KaziToad.stl

As an active member of this Tier you are granted a **Commercial License** to sell physical prints (online or in-person) made from my Regular models. 

***No selling or distributing the 3D Files***

I also encourage you to collaborate with me by giving feedback on existing models and suggestions for new ones. I can't wait to see what we can do together. 

Regular Model- Commercial License

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

To add to the #MakerMadness theme I have added some accessory, because what says "spring" more than a robot wearing sunglasses and holding a flower 😁.

Link to the Rock version:
https://thangs.com/mythangs/file/55887

Print Settings:

No support!
No brim!

The point of the Benchmark Bot is to find the best parameters to make it function, therefore it is difficult to recommend any settings.

That being said, I used the following parameters:
0.4mm nozzle, 0.2mm layer height, PLA, 3 walls, 4 top/bottom layers, 10% infill.

Benchmark Bot

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

Benchmark Bot (Kazi Toad)

Benchmark Bot Flower

Benchmark_Bot_sunglasses_KaziToad.stl

watering can

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Here is vase number 7, it is a unique twisting and crossing pattern. 

It is specifically designed to be printed in spiral vase mode, printing with one continuous outer wall, to print quickly, without a seam and no support.

I suggest using a large nozzle, line width, and layer height. I also suggest printing in spiral vase mode with 4 bottom layers and only 1 outer wall.

If you like this, take a look at my other models :)

Twisted cross Vase (Vase No. 7)

Here is vase number 7, it is a unique twisting and crossing pattern. 

It is specifically designed to be printed in spiral vase mode, printing with one continuous outer wall, to print quickly, without a seam and no support.

I suggest using a large nozzle, line width, and layer height. I also suggest printing in spiral vase mode with 4 bottom layers and only 1 outer wall.

If you like this, take a look at my other models :)

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This is a semi-realistic Christmas tree that can be illuminated with an ELECTRIC tealight (no flames please).

The best part is: it can be printed in vase mode, that means no support, no seams, thin walls for illumination, and it prints super fast.

The tree is 75 x 120mm, with a 40mm hole in the bottom. Feel free to scale it up or down to fit your needs.
Print with spiral vase mode.

Suggested settings:
- 5 bottom layers
- 0 top layer
- 0.2mm layer height
- 0.6 line width

Checkout my geometric tree [here](https://thangs.com/designer/Kazi%20Toad/3d-model/Vase%20Mode%20Christmas%20tree-38831?manualModelView=true).

Tealight Christmas tree

This is a semi-realistic Christmas tree that can be illuminated with an ELECTRIC tealight (no flames please).

The best part is: it can be printed in vase mode, that means no support, no seams, thin walls for illumination, and it prints super fast.

The tree is 75 x 120mm, with a 40mm hole in the bottom. Feel free to scale it up or down to fit your needs.
Print with spiral vase mode.

Suggested settings:
- 5 bottom layers
- 1 top layer
- 0.2mm layer height
- 0.6 line width

**Hi, I'm Kazi Toad!**

I have a passion for designing things on the border between fun and functional.

Become a Kazi Toad member to receive access to **Premium Models** and a **Commercial License** to sell prints made from my designs.

Let me know if you have any questions: kazitoadprints@gmail.com

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Kazi Toad

Achievements

Fan Favorite

Sapling

Trailblazer

Pinned models