80mm fan shroud 30mm high with 90-degree air deflection.

Walls of v2 model are about 3mm thick and requires significantly less support.

I made this for the cooling fan in the base of my Type A Machines Series 1 3D Printer.

80mm Fan Shroud

80mm Fan Shroud v2.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842990.

40mm Fan Deflector for Type A Machines Series 1 3D Printer

50 degree deflection

No supports required

40mm Fan Deflector

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5851846.

Front Grille Assembly for 1st Gen Scion xB (2004 - 2006)

Remixed from jawhnbot's thing 5470117

Channels in the back for led light strips.

Toyota Part #: 52133-52051 & 52134-52051

Support required

Front Grille Assembly for 1st Gen Scion xB

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5482050.

Reconstructed car body/fender/bumper/panel clip thing 4255488

Tried to make this PLA friendly, but it is too brittle. Better off using stronger filament / resin.

Bumper Fastener Rivet Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842973.

A Snowflake Ornament to Hang Anywhere You Wish

Snowflake Ornament

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842970.

My laptop wasd keys get really hot when playing video games, to the point it sometimes burns my fingers. This silly little fan duct remedies that by cooling my Acer Nitro gaming laptop keyboard, blowing air over the surface.

It uses three 40mm noctua fans and rests on whatever is plugged in to the usb ports.

Keyboard Cooler

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5548207.

Press-fit hub for a 6001 bearing

Screw holes are 4.1mm wide and spaced apart 50.5mm from center to center

Two versions available - top-mount and drop-in

6001 Bearing Hub

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842977.

A little weather vane made out of circles.

You will need:
Minimum 200mm x 200mm Build Plate
x1 6001 Ball Bearing
Glue

Assembly:
Print the two sides of the Vane
Glue the two sides together
Print the base
Insert 6001 ball bearing into the base's center (press fit)
Insert the glued vane pieces into the ball bearing

Weather Vane

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5569983.

Optivisor Battery Cover Copy

Optivisor Battery Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5551851.

A base hub to spin an inserted 12mm outer diameter, 8mm inner diameter tube with reduced friction.

This hub utilizes a F12-21M thrust bearing and a 6001 ball bearing:
https://www.amazon.com/dp/B07QKKY9V2?psc=1&ref=ppx_yo2ov_dt_b_product_details
https://www.amazon.com/dp/B07FDXPVLP?psc=1&ref=ppx_yo2ov_dt_b_product_details

Designed to be mounted to a base via four M4 screws to support a spinning 12mm x 8mm x 1000mm Carbon Fiber Tube.

Comes in two printable parts: the hub base and the tube insert that the tube slides on to, which spins on top of the thrust bearing.

Ball Bearing Hub for Vertical Tube

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842987.

This is a completely redesigned z-axis leadscrew knob for the discontinued Type A Machines Series 1 3D Printer. 

It has the Type A Machines logo on the top, solid hub to hug the lead screw, and a more aggressive design for grip as well as style.

No support required. 

Z Axis Leadscrew Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842981.

A Knob for a Kitchenaid toaster; fits inside of a potentiometer that controls toasting level.

Print with supports with the front and back along the x-axis or y-axis for max strength.

Preferably use a filament material that is heat resistant.

Toaster Knob for Kitchenaid Toaster

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5501026.

3D-Print-Friendly replacement clip to replace the original middle sprayer clip on a Frigidaire FDB2410HIC3 dishwasher. 

Make sure you use the right filament! Choose a robust, high-temperature filament with chemical-resistant properties.

The original clip that held the middle sprayer together kept coming undone, allowing the sprayer to fall off. This print easily fixed that issue.

Frigidaire Dishwasher Middle Sprayer Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5842966.

A small trellis for plants that can be stacked.

Support touching the build plate required for the stakes. 

No support necessary for the trellis

Stacking Circle Trellis

A little sculpture that is supposed to be a drop of water splashing on the ground. Good size to hold business cards.

Sploosh

Sploosh.stl

Glasses frame designed around using two 40.5mm polaroid polarized lens filters for seeing through water and glass reflections. The lens filters are press-fit. There are slots at the top of each lens to allow easy rotation with a finger. The filters are able to spin to allow the wearer to select which orientation of light is allowed to pass through.

https://en.wikipedia.org/wiki/Polarizing_filter_(photography)

I made these glasses so I could see the animals in my local creek without the glare from the sun reflecting off the water. However these glasses could have other types of filters (like UV) in order to attain different effects.

40.5mm Filter Glasses

40.5mm Filter Glasses v18.stl

ModelA pocket pinball design based on old-timey pinball machines.

**Requirements:**
x1 M3 machine screw preferably 20mm or longer
x1 compression spring that can fit over the screw (some pen springs will fit)
x1 M3 nut, preferably a lock-nut type
6mm diameter ball bearing or airsoft pellet. Smaller sizes (like a bb) should work too
_**Optional:**_
x1 extra return spring for the ball launcher
x1 transparent glass or plastic shield so the ball doesn't pop out (10cm x 7cm)

**Assembly:**
1. Insert M3 screw into hole at the bottom right corner
2. Slide compression spring over M3 screw in the ball launch gutter
3. Screw M3 nut onto the M3 screw
4. Drop a ball into the gutter
5. (Optional) Glue a transparent sheet of glass or plastic on top so the ball doesn't fly out.
6. Enjoy!

Pocket Pinball

Pocket Pinball.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Justin B

Achievements

Seedling