Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4600626.

3D Printed mount for the awesome [GRBLHal Teensy 4.1 breakout board](https://www.tindie.com/products/philba/grblhal-breakout-board-unkit-for-teensy-41/) from Phil Barrett. This mount includes provisions for a [Micro USB Male -> USB Type B Female adapter](https://www.amazon.com/dp/B07G4XYJ5W/ref=cm_sw_r_tw_dp_x_IO0BFb2QSQS1V) allowing it to be zip tied to prevent vibrations from shaking anything loose. Included all source files as well as a version without the USB support. In my controller box I used a piece of steel sheet metal drilled/tapped to mount my motor drivers and other electronics. Used this piece to isolate the board from the grounded sheet metal.

If you notice the copper tape covering the USB connector in my photos, I snaked the USB adapter through expandable tinned copper braiding, covered other exposed areas in copper tape and soldering both to a ground lead in order to shield it from EMI. I'm unsure if it's absolutely necessary but I'd rather not have to go through the process of troubleshooting an issue that could've been prevented with a little extra shielding.


Other Links:
https://github.com/phil-barrett/grblHAL-teensy-4.x GitHub project page for grblHAL teensy

grblHAL Teensy 4.1 Breakout Board Mount w/ USB Cable Support

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3155534.

A sliding cup holder I designed for my computer desk to prevent spilling coffee on my keyboard whilst designing other objects! Stows away while not in use.

Requires 4x M3 standoffs and 8x M3 screws 15-20mm long as well as 4-6 tapered head wood screws (~3/4" long or 20mm) for securing tracks to the desk. I used 24mm long standoffs, but you can use whichever length and style suits you.

Print 1 of each: slide / lower
Print 2 of each: tracktop / bottom

Designed in so many different pieces so that the parts that are sliding together are all from the bed side for smooth movement.

To assemble screw wood screws through both printed track parts with the top of "cupholdertracktop" facing the top of the desk matching the tapered part of the ring piece. Screw one track in, put assembled cup holder in between them and screw in other track.

Under desk Sliding Cup Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4324967.

Auber 25A Heat Sink 3d Model for 3d printer design. Using the heatsink for 100A low resistance DC SSR to control the heated bed on my Taz 5 SKR upgrade. Parametric Inventor IPT source included for the heatsink. The SSR itself isnj't my work, but provided for convenience. https://grabcad.com/library/solid-state-relay-7

Auber D4825 SSR 25A External Heat Sink HS25ET

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3172456.

Mount an AKK X2 Ultimate on a 30x30 stack, held down with zip ties. Bottom open for airflow

AKK X2 Ultimate VTX 30x30 Adapter Plate

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:962402.

* By request: If you don't have a printer sufficient enough to print these I can send you a kit of 2 clips printed in strong ABS or PETG including hardware for $9 + shipping (US), just shoot me a message and I can ship it out within a day or two.

Disassemble wrist rest and remove old broken clips, use new clips to mark where the holes need to be drilled. Drill hole large enough to perfectly fit screw. The holes are sized for 2-56, 100 degree pan head SS milspec screws I sourced from mcmaster (Part #: 90471a115). There was barely enough space behind the plastic for the 2-56 nuts so I doubt any bigger screws/nuts will work.  

These are for the K70 RGB version but it seems that Corsair's whole line of mechanical keyboards are very similar in build so it may even work for the other models with less/more keys.

Corsair K70 Wrist Rest Clip Replacement

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1091238.

Works well with my Dean 6-string banjo, made it a little over a millimeter shorter than the bridge that came stock with it as I wasn't happy with the action. Included Inventor IPT file for your editing pleasure.

6 String Banjo Bridge

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4385426.

This is a project I worked on a long time ago and never really brought to my full vision since I lost interest in FPV / quadcopters and got more into building 3d printers / cnc's. I might put some more work into it though since I'm currently out of work bc of pandemic. So this is meant to mount a standard fatshark dominator / HDO compatible receiver module into this 3d printed box, it's shaped exactly like the goggles so any module that fits into your goggle will fit nicely into this. Just need a PCB and female header pins, some M3 screws.

I'll add more instructions needed as far as the wiring and stuff soon, you can find many DIY projects similar to this on YouTube on great channels such as ":Drone Mesh".

I put a lot of time into perfecting this design, I was originally planning on selling the plans to it but never did fully flesh out my vision. But if there's enough interest I may put some more work into it. Just let me know in the comments what you'd like to see (1/4-20" nut for mounting to tripod, etc). Tips are very much appreciated especially during these hard times since I'm running on what little savings I have and what little side work I can find.

[YouTube - Printed Part Preview](https://www.youtube.com/watch?v=gaG-V1tRxNU)

[YouTube - Working Prototype](https://www.youtube.com/watch?v=PEDYrzfD-k4&t=2s)

DIY Dock King Fatshark VRX Module Holder for Ground Station

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3146360.

An under the shelf hook / holster for a datavac electric air gun. Two 3mm screw holes for mounting. You can print with or without supports depending on object orientation. I printed in ABS with a 0.6mm nozzle and 0.35mm layer height for strength. 50% infill

DataVac Under Shelf Hook / Holster

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3146370.

An under desk or shelf holster / hook for harbor freight brand chicago electric 12 setting heat gun, faces the action end down but I would suggest mounting far enough away from anything combustible. Printed with 0.6mm nozzle 0.35mm layer height in ABS for strength. Can be printed with or without supports depending on object orientation. Works great for my workshop, hopefully this finds use somewhere in someone else's workshop!

Under Desk or Shelf Holster / Hook For Chicago Electric 12 Setting Heat Gun

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3116727.

* If you don't have a printer to make this for yourself shoot me a message

These are parts to increase the height of the canopy on the stock emax Babyhawk Race to better accommodate a camera with a larger lens such as the Runcam Micro Eagle without having to cut anything or make any modifications that can't be undone. This should allow you as much camera angle adjustment as before the mod. Pictured I used the rakonheli cnc aluminium frame kit but it should work on the stock carbon fiber frame as the mounting holes are the same dimensions. Just print the shim as well as the bottom piece and reassemble as normal using the M2 nuts that came with it. May require longer M2 screws in the shimmed part.

Edit: had a couple of hard crashes that bent the arms on my aluminium frame and broke off a motor bell, but the Micro Eagle is still in perfect shape so confirmed that this provides adequate protection for the massive lens on the camera! 

Enjoy and safe flying!

Babyhawk Race Lift Kit for Runcam Micro Eagle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3515753.

Printed out of TPU flexible filament, an insert pad meant to use with resistance workout bands when doing curls and whatnot without hurting your big bare sasquatch feet. Sized it to the higher resistance bands so should work with any of them.

Resistance Workout Band Foot Hold Pad

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4613766.

Huanyang VFD Line Filter extension box created for my hy01d511b. Used M5 screws and nuts to mount the line filter, M2.5 screws and threaded inserts for mounting the supports (they only are to prevent the enclosure creating flex. To mount to the VFD I used the enclosure as a template for drilling holes into the VFD box using 4x M3 screws and 4x nyloc nuts to secure the enclosure to the Huanyang VFD. The strain relief screws in with M2 Screws and threaded inserts. If your Huanyang isn't genuine or you're unsure if it will fit I've provided a fitment test you can print to see if it will work before printing the whole thing.

Huanyang VFD Line Filter Enclosure / Extension Box With Strain Relief

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3271494.

Print at 102-104% scale, remixed from McBane's design dimensions and ribs added for durability and style. Heat up the top with a torch for easier installation.

A different Pagoda TPU Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3317346.

Print at 102-104% scale, remade using McBane's design dimensions. Added geared look to top for style. Heat up the top with a torch for easier installation.

Pagoda TPU Cover Studded and Stylish

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4166380.

I wanted this sander but didn't want to pay $6 for the actual sander part so I just purchased the belts and modeled this around these:

https://www.amazon.com/dp/B01IRLEALI/ref=cm_sw_em_r_mt_dp_U_uHvsEbQ2TMASE

Using those yellow 3D printer bed springs:

https://www.amazon.com/dp/B07SCYM119/ref=cm_sw_em_r_mt_dp_U_9OvsEb1H3GHA7

If you'd like to print these separately to fit on a smaller bed in Simplify 3D go to Mesh > Separate Connected Meshes.

Sanding Detailer (Spring Loaded For Mini Sander Belts)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3317368.

Printed from TPU this strap is designed to hold a power brick (e.g. aquarium lighting power supply) of multiple different sizes using one or two screws and a zip tie. Print using lower infill for maximum stretch-ability, the grippy nature of flexible filament holds them in place quite nicely with minimal time/material cost. Haven't tested this on many different size power bricks, so let me know if some modifications to the design are needed for your application.

Edit: Added a thinner and textured version

Power Brick Mounting Strap TPU

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3146384.

A little 3d printed adapter piece for installing a 20x20 vtx onto a holybro kopis 1 frame while still using stock antenna holder. Had to offset the 20x20 mounting holes back a bit for the coax cable to be able to reach. An unintended advantage to this is moving the VTX further back away from the gyro therefore possibly isolating it a bit more from electromagnetic interference. Doesn't seem to affect the balance of the craft at all, also includes a slot and cutouts to zip tye receiver and any loose wires. Hopefully this finds someone some use. 

Thanks to those generous folks out there that have shown their gratitude with the tip button, it encourages me to share more of my designs and keep contributing to this amazing hobby of FPV.

Holybro Kopis 1 20x20 VTX offset adapter`

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3452090.

Thanks to Not1ofthepack, remixed to add some beef to it. when printing his original model I wasn't happy with the amount of flex in the part so I added onto the model in inventor. Because of the way I edited it there are multiple solid bodies and self-intersecting surfaces in the model which may cause a problem slicing. In Simplify3d you simply position the model on the bed, click Mesh > Separate Connected Surfaces and it should print fine. Printed mine in PETG with support. I had to add two nuts to each side to lower the bltouch to the correct position for my extruder/nozzle setup (hexagon hot-end same as stock taz 5).

The firmware I used was kindly forked from a recent aleph objects build by Menissalt on the lulzbot forums: https://forum.lulzbot.com/viewtopic.php?f=16&t=6809

You'll need to figure out your Z-offset values, a good video showing how can  be found here: https://www.youtube.com/watch?v=y_1Kg45APko

Configuration.h values:

define X_PROBE_OFFSET_FROM_EXTRUDER -26
define Y_PROBE_OFFSET_FROM_EXTRUDER -34
define Z_PROBE_OFFSET_FROM_EXTRUDER (leave, change this after flashing)

define LEFT_PROBE_BED_POSITION 20
define RIGHT_PROBE_BED_POSITION 240
define FRONT_PROBE_BED_POSITION 20
define BACK_PROBE_BED_POSITION 240

BLTouch LulzBot Taz 5 Add-On

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3200999.

Couldn't find anything like this on thingiverse so I designed my own, wanted easy access to my cutters, strippers, needlenose and solder sucker for when I'm doing some soldering. Mounted mine on a bit of an angle for ergonomics and works great thus far!

Screw holes are included in the design but I've found it mounts perfectly fine with some double sided foam tape.

Tool Bench Holster for Plyers and Solder Sucker Soldering Tools

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3482579.

While drinking a couple adult beverages with an old friend he mentioned he needed something to hold a 9v battery for electronics in the guitar he's building. After a quick search finding nothing like he needed I decided to whip up the design myself real quick.

This allows you to use the existing battery terminal clip and lets you easily slide the battery out for replacement, inset mounting square for foam mounting tape.

Originally printed in PETG and it's snug enough, you may need to adjust the scale by a few percent for other filaments or better fitment for your situation.

9v Battery Holder Sleeve

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1226541.

Modified the bottom plate for the official DJI F450 Top Plate, so that the holes line up for passing wires through. Thanks to original author Guy McCaldin!

Weighs about 9 grams printed in ABS.

Modified Omnimac 3DR Pixhawk Anti Vibration Mount For DJI F450 (originally by GuyMcCaldin)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3235656.

All the existing versions out there didn't work with the Panasonic FR Series 1000uF 35v caps I have so I redesigned it for my use. Printed and tested to work in ABS as well as TPU/Ninjaflex Cheetah

XT-60 Capacitor Holder For Panasonic FR Series 1000uF 35v 13mm

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

JiMaker

Achievements

Sapling

Debutant