Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5994377.

A model of a Steward platform or a Hexapode.

Watch it in Action (https://youtu.be/gH8y91gmtwc).

You can choose which Base you wanna use. In this Pictures i've used the small and the big one but because the interfaces are identical you can use whichever you want. In the Comunity Print section you can see Pictures where i've used the middleBase as Top and as Bottom. 

Size in this configuration 150x125x85mm.

Additional you will need:

6x Screw M3x15

6x Screw M3x25

6x Screw M3x35

18x Hexagon Nut M3

The Screws can always be longer. They can also be replaced with some Filament or something simular however, this can fall out when moving, which can reduce the fun of the model.

Stewart platform

a wallmount for a safety razor.
Cause it's mostly used in Bathrooms there is no hole to screw it into the wall. 
I think it's best to glue it with some doubblesieded tape.
Make sure to check out my other razor holders

wallmount safty razor

a normal holder for a safety razor.
It's a realy simple design.
Check out my other razor holder

razor holder normal

a minimal holder for a safety razor.
It's a realy minimalistic design.
Check out my other razor holder

minimalistic razor holder

This is a travel cover which snaps in place with a little nose on the Razorhead.

It prevents you from cutting yourself or the inside of your bag when you take it with you.

I prited it laying down flat with suport, but i think you could print it without suport with a good printer.

Safety Razor Travel Cover

A showerholder for a safety razor.

Just snaps in place.

Should work for every tube with an diameter of 25mm.

Showerholder Safety Razor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4899612.

A Crown Gear with Module 1 and 42 Teeth, the Pinion has 40 Teeth.

The Diameter on the outside of the Crown Gear is 52mm.

The Pinion is a normal cog without any special geometry. It is 10mm wide.

Crown Gear Module 1 Teeth 42, Pinion Module 1 Teeth 40

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4877796.

Holder for an HC-SR04.
50x25x5mm.
Hole d2mm at the top, conical widens to 3mm.
Perfekt to mount the Sensor with a small wire.

Designed in Siemens NX. The .prt is also included if you want to customiz it :)

HC-SR04 holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4899620.

A Crown Gear with Module 2 and 21 Teeth, the Pinion has 20 Teeth.

The Diameter on the outside of the Crown Gear is 54mm.

The Pinion is a normal cog without any special geometry. It is 10mm wide.

Crown Gear Module 2 Teeth 21, Pinion Module 2 Teeth 20

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4899607.

A Crown Gear with Module 1 and 42 Teeth, the Pinion has 14 Teeth.

The Diameter on the outside of the Crown Gear is 55.9mm.

The Pinion is a normal cog without any special geometry. It is 10mm wide.

Crown Gear Module 1 Teeth 42, Pinion Module 1 Teeth 14

Refence model for working with an 0.91" OLED Display (128x32 Pixel).

Download as an stl or step possible.

0.91 OLED Display 128x32 Pixel, Refence Model

0.91-OLED-128x32.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Feeee23

Achievements

Seedling

Debutant