Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4551180.

Hello :) I remixed the Switch lite grip from icefox1983, to fit the print bed size on my anycubic Photon s in one single print and no Gluing!

### Things I modified:

1 - Separated both halves
2 - Added Notches to use rubber bands as the middle piece to hold both halves in place
3 - Smoothed the Grips surface
4 - Embossed little Hearts on the top trigger supports :3
5 - Adjusted the Sizes and dimensions to my switch lite (due to the resin post curing shrinkage etc...)
6 - Pre-supported them and arranged them on the build plate (very tight fit!)

This way, you can print both of them in one go, and use them as is with no gluing! Also this design saves on resin, and weight in your backpack!

### Printing!

You can basically just use the pre-supported pre-sliced .photons file IF you have a Photon S. 

In that case, adjust the exposure settings to your resin directly during printing (start the print, then the cogwheeel button let you do that).

The Print settings/parameters I used (and baked in the sliced file).

Bottom layers exposure time: 80 s
Bottom layers number: 6
Normal exposure time: 5 s
Layer thickness: 0.02 mm

Real Printing Time: around 14 Hours (estimated to 12h in the slicer)
Resin consumption: around 60-65 mL

Resin I used: Anycubic plant-based ECO pink
Temperature during my print: 25-28 celsius

### Post Printing!

The ususal:
1 - wash
2 - remove supports
3 - dry
4 - cure under lukewarm water
5 - sand supports knobs

Then you just need two average sized rubberbands and a nintendo switch lite!

(Place the rubberbands like you can see in the picture up there)

Switch Lite Grip - PRE-SUPPORTED RESIN EDITION!

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4382611.

### A skyrim logo necklace! 

Original model by: https://www.thingiverse.com/thing:3042456

I basically adapted it to a simple necklace, thicker, added proper support, an attachment point etc...

### Printing!

I included my supported stl's as well as the sliced files for the anycubic photon S.

### My print settings: (in use in the pre-sliced file)

Printer: Anycubic photon S

What to print?: 4 double sided skyrim necklaces at once

Time to print?: around 8 hours

Layer height: 0.02 mm

Quantity of resin used: around 20 mL

Type of resin: Anycubic Eco plant-based resin (macaroon pink and blue)

Printing temp: around 20C, the highest I could get at the time

###Washing, Curing

I recommend removing the supports before curing. It's a bit more tedious with gloves and a mask, but they come off easier and there is less risk of damage.

also recommending to cure underwater, just tried with the last batch and they came out great.

###Sanding

I started with 100 grit, then 150, 250, 600 grit.

Basically sand the supports marks until they are flat, then increase the grit to have a smooth finish.

###Painting

I did two thin layers of black primer, then two layers of shiny chrome, short 

### /!\ WARNING /!\

I left the first three ones I printed on my desk in the sun before painting and they started to warp after 2-3 days. so maybe avoid leaving them in the sun before painting. (or cure them more).

### Have fun :)

Skyrim logo necklace

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4407250.

### A phone stand with a hidden wireless charger inside! 

Made for this exact wirless charger: https://www.digitec.ch/de/s1/product/xqisit-wireless-fast-charger-1a-10w-quick-charge-20-fast-charge-mobilgeraet-stromversorgung-8763156

I would basically not use my wireless charger because I'd need to carefully aim for it to charge and couldn't use it while charging... Ss I made this stand!

it's way easier to hit the fast charging sweet spot and I can use my phone in landscape mode while it's charging!

### Printing!

I included my supported stl's as well as the sliced files for the anycubic photon S.

In cas you want to modify/hollow/pierce/orient/support the model yourself, you'll find two base models: 

- WirelessPhoneStand.stl
- InternalSupports.stl

Basically, I don't like auto-generated internal supports (when you hollow the model) So I manually designed some permanent ones.

Long story short, in case you want to apply modifications the workflow is as follows:

- Modify "WirelessPhoneStand.stl"
- Add fill supports to the wireless charger hole port.
- Orient the model on the build plate (-90 degrees X and -6 degrees Z)
- Hollow the model, min 2.5mm thickness
- Add draining holes, take a look at my ready_to_print stl for guidance
- Add the "InternalSupports.stl" model, place it under the big internal overhang, (under the slot for the wirless charger)
- The internal supports should go though the first wall resting on the build plate and though the first wall of the wirless charger slot (without poking on the other side!).
- Slice them both at the same time an print it!

### My print settings: (in use in the pre-sliced files)

Printer: Anycubic photon S

What to print?: One phone stand with an hidden slot to put a QI wireless charger

Time to print?: around 24 hours

Layer height: 0.02 mm

Quantity of resin used: around 160 mL

Type of resin: Anycubic Eco plant-based resin (macaroon pink)

Printing temp: around 20C, the highest I could get at the time

###Washing, Curing

I recommend removing the supports before curing. It's a bit more tedious with gloves and a mask, but they come off easier and there is less risk of damage.

also recommending to cure underwater, just tried with the last batch and they came out great.

###Sanding

Basically sand the supports marks until they are flat, then increase the grit to have a smooth finish.

### Have fun :)

Wireless charging phone stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4912138.

Hi, unfortunately, I don't have a printer anymore, but I still wanted to share my creation in case anyone wants to print it (I would love to see the results!).

Please do share your print settings if you sucessfully print one :)

I made some changes in the original model, to make printing easier and the model more sturdy, but I would still recommend using a UV-resin printer and lots of supports ;)

Imperial Spaceship

SpaceShip.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Emma_Frch

Achievements

Seedling

Debutant

Switch Lite Grip - PRE-SUPPORTED RESIN EDITION!

Skyrim logo necklace

Wireless charging phone stand

Imperial Spaceship