Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6283829.

I Created a little holder for the Badge Card used for work access.
Because we require a separate RFID I looked for a nicer way than attaching it to the keychain. It unfolds with a hinge, so ID Card does not interfere with the RFID Chip.

Also we need a Locker key, which also makes sense to have close by to the ID Card. So this key also unfolds with an hinge, to make turning easier, as it is attached to the Badge Card holder.

Its best to print it standing up, so you barely need supports, and it doesn't deform the card insert.

As a little addition, I wanted to add a clip, so it does not need to be attached to a chain. For that I would recommend a softer filament, so it does not break while using it.
Also a word of caution: The Clip can cause the Badge holder to break when trying to remove it, but I haven't found a clever solution for this problem yet.


Badgecard Holder with RFID Attachment and Locker Key

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6283802.

I Created a little holder for the Badge Card used for work access.
Because we require a separate RFID I looked for a nicer way than attaching it to the keychain.

It has a hinge, because attaching it directly behind the badge card causes interferences with the readers. The hinge is set in place with the card in front of it.
If the Interference is not an issue, there is also a Version with the RFID Chip that can be placed behind the ID Card.

Its best to print it standing up, so you barely need supports, and it doesn't deform the card insert.

Badgecard Holder with RFID Attachment

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6283872.

Well on my car, the seal in the door came loose, which was annoying. Gluing it back on only helped for a few weeks.

So to attach the both loose ends of the seal I made this little fastener to stick inside to assist the glue by reducing downward force. (Even holds without the glue)

Just print two of those, interlock the two and stick it in the seal. Just be careful, that the door is not damaged if the plastic part doesn't fit too well.

Car Door Seal Connector

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6283755.

I Created a little holder for the Badge Card, nothing fancy.
The fancy stuff will be uploaded too in a bit.
Its best to print it standing up, so you barely need supports, and it doesn't deform the card insert

Badgecard Holder

All Ikea Cupboards have many unused holes. 
Especially in the kitchen that is a really attractive area for moths to lay their eggs.
For this reason this plug fits the holes of ikea cupboards, and all other 5mm holes for that matter.

It just takes a minute or so to print, and on my 20x20 print plate I can fit 20 easily. Coincidentally, it takes about the same time for me to place all the plugs in the cupboard, as the printer to create another batch.


Ikea Cupboard Plug

After heating a nice slice of toast it leaves condensation on the plate, which is then absorbed by the bread again, which makes it soggy again.
For the intermediate cool-down phase this stand will dry the toast, allowing condensation to be delivered to the air and not the bread.

Toast Dryer

Putting a flowerpot on a desk was a nice idea, but watering was very dangerous. So I designed a Version with a removable water tank, which can be filled with water and inserted in the pot. Inserting the tank in the pot will push open a valve and the water runs in the pot.
I can't guarantee a 100% waterproof design, but a better print quality may help with that.

Gridfinity Planter with Watertank

Gridfinity Flowerpot Assembly.stl

I want to create a clean and modular Desktop setup for the office using the Gridfinity system. A plant makes it feel more homely. Therefore I am adding a basket with a second floor and a watering compartment to be used as a flowerpot in the Gridfinity system.

Gridfinity Flowerpot Planter.stl

Adding a basket with a second floor and a watering compartment to be used as a flowerpot in the Gridfinity system.

Flowerpot.stl

Gridfinity Flowerpot Case.stl

Gridfinity Flowerpot Watertank.stl

Gridfinity Flowerpot Valve.stl

Card_Chip_and_Key.stl

Pins_for_fastening.stl

Hi and welcome to my Profile.

I am a Hobby-Maker and I often focus too heavily on solving everyday Issues, that aren't really that big of a problem.

Hope some designs can be used by other Makers, that want to solve the minor problems in life.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Dannybot prints things

Achievements

Seedling

Explorer

Debutant

Pinned models

Gridfinity Planter with Watertank

Badgecard Holder with RFID Attachment and Locker Key

Badgecard Holder with RFID Attachment and Locker Key

Badgecard Holder with RFID Attachment

Car Door Seal Connector

Badgecard Holder

Ikea Cupboard Plug

Toast Dryer

Gridfinity Planter with Watertank

Gridfinity Flowerpot Planter.stl