Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3016382.

Yet another CR10 remix for the CR10\CR10S Control Box.
This is yet another remix of the marvellously minimalist Spool Holder by filamentry but with a stability\mounting tab added. You will still need 2 bearings per assembly.

I purchased mine here:
https://simplybearings.co.uk/shop/advanced_search_result.php?search_in_description=1&keywords=608zz

1.I have incorporated fixing tabs which relate to the existing spool holder fixings on the control box.
2.Incorporated grips \down stands to prevent spool moving out of position.

Apologies in advance if there is already a similar remix that I have not spotted.



TUSH Spool Holder for the CR10\CR10S

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4222506.

This is my side mounted extruder stepper motor bracket for the Hypercube Evo using 3030 extrusion.

I have included a step file for personal derivatives.

Printed in Amazon Basics PETG on an Ender 3 Pro

Hypercube Evo Side Mounted Extruder Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3103756.

Zonestar P802QR2 60mm Fan Duct

About the only thing I have not had problems with the Zonestar P802QR2 is layer cooling so this thing may be a little OTT.

The thing was inspired by a comment from the9rtyt regarding using 2 fans for cooling. Due to the fact I already am overloading the Zonestar`s cheap PSU with 2 additional fans already I thought that using one larger fan to spread the required cooling airflow might be an alternative solution. I have therefore designed a cooling duct which houses a 60mm fan to widen the origin of flow around the extruder assembly cradle.

Print Settings:

This thing does not need to be especially strong but being so near to the hotends using ABS or PETG may be better. I printed the thing @ 0.2 resolution, 2 perimeters and a 20% infil. The thing will probably print without support but I used some custom supports under the mounting bosses for a cleaner thing (see uploaded image).


I must stress this is definately work in progress. I have printed the thing successfully but have not tested it yet. You may have to change the fan mounting holes dependant on which type of fixing you prefer to use.


Zonestar P802QR2 60mm Fan Duct

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3003981.

DO NOT USE WHEN NOZZLES\HEATER BLOCKS ARE HOT!

Description:

Zonestar P802QR2 Nozzle Allignment Jig. The jig is an aid to aligning the two hot ends relative to each other. There may be some additional levelling required when levelling nozzles with the bed but I have found that it is much easier to achieve greater accuracy using the jig or something to bottom the nozzles on.

Features:

1. The design also prevents the heater blocks from rotating when attempting to level. 
2. The jig should be an inrterference fit but I have also included 2 x fixing tabs which fix to the exisiting Hot End Fan mount fixings.

Printing:

0.2 resolution, 20% infil with no support.

Collection of all my upgrades for the Zonestar at the following link:
https://www.thingiverse.com/thing:2936870



Zonestar P802QR2 Nozzle Allignment Jig

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2743636.

Simple Tripod bubble level to be trapped between tripod and image device. I specifically designed this component to be used with my Samsung Gear 360 and a monopod + stand to provide a guide towards the level of the tripod setup. The level can still be used with a standard camera if radial clearance allows. This is not perceived to be an accurate\precision aid to levelling. It helps greatly to have a guide when taking panoramic images.
You can find the Bubble vials on Amazon:-
Link: https://www.amazon.co.uk/gp/product/B01IR5IORU/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Tripod Bubble Level

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3098514.

This is a simple thing to elevate the Samsung One Connect Box off the base to allow additional air flow underneath the unit. I did not do this for any specific reason other than the box gets quite warm and thought this would aid cooling.


Printed @0.2 resolution, 20% infill. It does not require supports.

Samsung One Connect Box Elevated Leg (2017 Model)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3529550.

This is a Mask, Hat and Wig Stand. The design emphasis was minimalism and speed of printing.

In this remix I have separated the parts so that the thing can be printed on a 220 x 220 build plate at 100% or on a 200 x 200 build plate at 95%.
 
Conversely the V2  protoype was a little large for my Batman Cowl so therefore I probably should have reduced to 95%.

Parts are a reasonably tight interferance fit but can be glued for greater security.
Printing Instructions:
1.The things were printed fast using a 0.8mm nozzle, 0.6mm layer height and @40mms. 1 perimeter and 7% infill.
2.Further speed reductions may be achieved with only printing bottom layers and rely on the infill for rigidity. Average print time at these settings was approx. 35 minutes.

Cosplay Mask, Hat and Wig Stand V2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2888630.

Bird Spikes to keep Birds off a tiled roof. This is a remix of 3dbc`s thing but with a curved base plate to help glue to a curved ridge tile and increased width to base of spikes to make slightly stronger and easier - although longer to print. Remodelled in Fusion 360.

Due to the curved base plate the thing is best printed with a raft and support to the build plate.

Bird Spikes for a Curved Ridge Tile

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2936875.

Yet another thumb wheel for a M3 bolt.

Bed Thumbwheel with M3 retention

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3483303.

Simple scale model of a small form factor computer - scale 1:10

printed without supports in orientation uploaded.

Model Small Form Factor Desktop PC Scale:1:10

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3078781.

Simple thing to provide cables hoops above the motherboard to help tidy the various cables running vertically up the frame.

Simple Cable Hoops for the Zonestar P802QR2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2837183.

Simple frame to frame Lithophane and mini light box from Amazon
Light box Link: https://www.amazon.co.uk/gp/product/B0767LGTZM/ref=oh_aui_search_detailpage?ie=UTF8&psc=1


Picture frame for Mini Lithophane light Box - Simple

Multi-Disciplinary Professional Designer with 35 years contract experience primarily in Interior and Furniture Design. Since receiving a rebadged Duplicator Plus (Balco from Aldi) 3d printer from my wonderful wife for Christmas 2018 I am now using my design skills for personal 3D product creation

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Boothy

Achievements

Sequoia

Up and Coming