ForgeCore50K followers

Calla Lily Pens - Flower Pens, Bookmarks, and Pitcher Vase video thumbnail

Calla Lily Pens - Flower Pens, Bookmarks, and Pitcher Vase 3d model

Calla Lily Pens - Flower Pens, Bookmarks, and Pitcher Vase

1.4K downloads · 1 year ago · [Instructions](https://prinnit.com/ForgeCore/design/368QyqkW9dJTZiAGXcJfqmfnlrg?tab=instructions&hig

Description

Instructions Hardware Filaments

Calla Lily Pens - Intermediate - Single Color Printer Compatible

I wanted some pens I could leave out on the counter. without looking like clutter, so I designed these Call Lily pens! Each Stem has a pen and the flowers are the caps. There are also leaves that you can use as bookmarks.

The model also includes a pitcher vase which can be used as a real vase if you want, just make sure to print with 4 walls so its watertight.

This release is just in time for Mothers' Day!

Tags:

Community Makes (18)

any advice on this? Never had this happen before. I tired slowing the print down, tried using supports, but I get the same results. Using Flashforge AD5X printer with .4mm nozzle

Wow. I love this addition to my desk so much 🤩

Delightful. As is my custom for pots, I printed the vase with seam position set in my slicer to "random" instead of "aligned," since I prefer randomly patterned zits/bumps over a visible seam. To make the flower caps fit comfortably on the pens, I used a heat gun: holding the gun a couple inches from the base of the cap, on low setting, for about five seconds, before immediately pushing the cap onto the stem with the pen inside. (Heat guns come in different powers, so YMMV.)

With some modifications I finally managed to print the stems one at a time. But now I am not sure how this is supposed to work but the pen hangs out too much from the stem and the plug part just sticks out from the back? This is a g2 refill as listed.

Printed in Polymaker cotton white, flamingo pink, yellow and bambu basic green

Turned out great. No problems putting the parts together.

This was a fun make!! Calla lilies are my sister in law's favorite, so I made these for her to celebrate mother's day 💐 Now she has an everlasting set!

I would have given it to my mom, but she lives 20 hours away from me unfortunately. Now she'll just have to wait till she comes down in June for it.

I'm very pleased with the outcome; my mother is also thrilled with it because it's both practical and attractive for her desk and work area.

Printed for my mother in law for Mothers Day! Her favorite color is purple and I found a beautiful lavender that looked stunning with this print and it turned out amazing! Printed vase in marble pla with flowers and stems printed in pla as well. Overall, great print!

This design was made for me! I love Calla Lilies. I made 2 with completely different vibes, I'm in love with both of them. Which do you prefer?

Calla lily pens and bookmarks. Numakers bright white, grass green, and forest green. Gifted it to my other half for Mother's Day. :)

Used Overture Matte White filament for the vase so the kids could paint it. Used pink and gold dual color filament for the petals, shiny green for the stems and leaves, gold for the centers. This one is for our family! Sold some white ones with a silver vase at a fair earlier! LOVE THIS MAKE!

I love that these print without supports, it’s a fast print and I don’t need an AMS. It’s perfect in so many ways

Community Makes (18)

Discussions

MikeMoans1 year ago

Printed in Polymaker cotton white, flamingo pink, yellow and bambu basic green

PrinterBambu Lab P1S

MaterialPLA

YoungPrint3D1 year ago

I love that these print without supports, it’s a fast print and I don’t need an AMS. It’s perfect in so many ways

PrinterBambu Lab A1

thecraftycafe.nv1 year ago

Hi! I love how your print turned out! Can I please ask you how you assembled the pens since he didnt make a video this time. I get the basic just of it but for some reason my flowers hole in the bottom of them do not fit to the small round sticks that I only assume fit on the end of the pen into the flower to keep it attached. But, you seemed to not have anh problems. Please help! Im leaving in less than 2 hours for a show and I have 3 sets to put together and im frustrated and feel so stupid...

YoungPrint3D1 year ago

You put the yellow piece into the flower from the top. You probably want to use glue so they don’t fall out. The pen slides into the larger hole tip first and the plug helps push it into place. Using a heat gun makes it slide easier for me. The helpful instructions pdf shows this all too though if you didn’t look at that

suz.boltz1 year ago

When I do that it’s is pushing out the pen.

YoungPrint3D1 year ago

A quick fix, since you are short on time, is to use a heat gun to get them to fit all the way!

thecraftycafe.nv1 year ago

Thank you! My PDFs NEVER open from him and IDK why because I can print everyone elses just fine. I appreciate you!!

YoungPrint3D1 year ago

I hope you get it figured out! The PDFs are super helpful!

thecraftycafe.nv1 year ago

Thank you so much for your help. Unfortunately I did not get it figured out, still. I tried several times and for the life of me can not get the pens to work, one even broke at the tip and ink went everywhere inside the pen tube luckily so I just threw the entire piece away. I was extremely sad though because I wanted to give this to my mom on Mothers Day. All I gave her was the pitcher that I did make watertight, and the leaves for now. Until I get these damn pens figured out or I find a video

Twin3d1 year ago

This design was made for me! I love Calla Lilies. I made 2 with completely different vibes, I'm in love with both of them. Which do you prefer?

PrinterBambu Lab A1

ShaoPeng Zhang1 year ago

Awesome, especially the fourth picture, perfect match

chesnye1 year ago

Used Overture Matte White filament for the vase so the kids could paint it. Used pink and gold dual color filament for the petals, shiny green for the stems and leaves, gold for the centers. This one is for our family! Sold some white ones with a silver vase at a fair earlier! LOVE THIS MAKE!

PrinterBambu Lab P1S

MaterialPLA+

Infill density15 %

SupportsNone

Talridam9 months ago

Wow. I love this addition to my desk so much 🤩

PrinterFlashforge Adventurer 5M

MaterialPLA

ForgeCore9 months ago

Thank you for sharing!

pyration1 year ago

I would have given it to my mom, but she lives 20 hours away from me unfortunately. Now she'll just have to wait till she comes down in June for it.

PrinterAnycubic Kobra 3

MaterialPLA

info7558668 months ago

I love the black petals

wilsonc0021 year ago

alianoraree9 months ago

Delightful. As is my custom for pots, I printed the vase with seam position set in my slicer to "random" instead of "aligned," since I prefer randomly patterned zits/bumps over a visible seam. To make the flower caps fit comfortably on the pens, I used a heat gun: holding the gun a couple inches from the base of the cap, on low setting, for about five seconds, before immediately pushing the cap onto the stem with the pen inside. (Heat guns come in different powers, so YMMV.)