GEN2 270 Classic Drawers

270-1W-1H Classic Drawer.stl

Lamp “Bonbon”

Bonbon_desk.3mf

GEN2 185 Decor Drawers - All

Decor Drawer 180-1W-05H.stl

Simple Stackable Tea Bag Dispenser

tea-bag-holder-assembly.3mf

ClampDock Accessory - Pocket 60Wx40Dx100H (for pens, glasses, remote, etc)

ClampDock 1v00a Small Pocket.stl

Mushroom vase “Gleophyllum Abietinum”

**A unique vase for flowers.**

**Scaling / size**
- Upscaling (100% +): as big as you want
- Regular size (100%): 168 x 165 x 216 mm – has a wall thickness of 2 mm
- Smaller (80%): 134 x 132 x 173 mm – has a wall thickness of 1.6 mm
- Minimum size (60%):  100 x 99 x 130 mm – has a wall thickness of 1.2 mm
- Everything smaller than that is not tested but probably possible

Don't forget to post your makes!

**Print settings**
Material usage (100% scale): 270g
Print time: (100% scale): 22h

Material usage (80% scale):160g
Print time: (80% scale): 13h

Material usage (60% scale): 80g
Print time: (60% scale): 7h

Material: PLA
Print direction: stl is rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm
Outer walls: 3
Infill: 15%
Build plate adhesion type: none

Watertight printing: If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), increase print temperature, check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

If you experience any problems, please feel free to contact me on twitter or Instagram


Vase “abietinum fungus”

Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Lattice Christmas Ball

ClampDock Accessory - Design Blank

ClampDock 1v00a accessory blank (with support).iges

GEN2 Table Top Kit V2 - 115

Cover - Upper - Single -  MEDIUM.stl

BMO - Print In Place

BMO - Print In Place easy to print. no support needed.

happy printing 

Cat & Dog Food Bowl Raiser Stand Ø

Alzaciotola L 22x22x16.3mf

TULLE COASTERS | FABRIC + PLASTIC

COASTER - PRINT ME! (BAMBULAB).3mf

Garlic night light "Gary"

All.3mf

CALIZ  |  Woven Table Lamp E14 & E26/27

CALIZ_table-lamp_short_V1_Base.stl

Marshmallow table

Marshmallow_Table.3mf

TELA  |  Table lamp E14 & E27 & E26 fast print

TELA_table-lamp-Shade.stl

Paper Bag Vase

Paper Bag Vase.stl

tool holder cricut tools

tool-holder-cricut-tools

GEN2 Decor Gridfinity Drawers - Standard

GEN2 Decor Gridfinity Drawer Double - Standard.stl

Tensegrity Table print-in-place

This is a print in place tensegrity structure that is held in place by strands of printed filament.

When printing use 0.3mm layer height and no supports. When sliced you should be able to see the single strands of filament.

Table

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

GEN2 270 Classic Drawers

Lamp “Bonbon”

GEN2 185 Decor Drawers - All

Simple Stackable Tea Bag Dispenser

ClampDock Accessory - Pocket 60Wx40Dx100H (for pens, glasses, remote, etc)

Mushroom vase “Gleophyllum Abietinum”

Starburst Christmas Ornament

ClampDock Accessory - Design Blank

GEN2 Table Top Kit V2 - 115

BMO - Print In Place

Cat & Dog Food Bowl Raiser Stand Ø

TULLE COASTERS | FABRIC + PLASTIC

Garlic night light "Gary"

CALIZ | Woven Table Lamp E14 & E26/27

Marshmallow table

TELA | Table lamp E14 & E27 & E26 fast print

Paper Bag Vase

tool holder cricut tools

GEN2 Decor Gridfinity Drawers - Standard

Tensegrity Table print-in-place