Momentus Mind Camera Basic // Fidget Clicker + Memory Device

Front.stl

Snappy Switch Keychain

SnappyOG_CaseBack_Keychain.stl

EZPZ Pegboard Hook // 25mm Reinforced Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 25mm depth and a reinforcing strut along the bottom, which takes up a bit more space in exchange for greater strength. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

EZPZ Pegboard Hook // 20mm Hook Type B

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 20mm depth and a shallow angle. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Big Snappy Indicator Switch

BigSnappy_CaseBack.stl

Icosahedron Pyramids // Folding Polyhedra Pack No.1

folding-polyhedra-pack-03-icosahedron-icosahedron-pyramids.stl

EZPZ Pegboard Hook // 20mm Reinforced Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 20mm depth and a reinforcing strut along the bottom, which takes up a bit more space in exchange for greater strength. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

EZPZ Pegboard Hook // 15mm Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 15mm depth. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

EZPZ Pegboard Hook // 20mm Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 20mm depth. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

EZPZ Pegboard Hook // 25mm Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 25mm depth. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Snapping Turtle Skull

Snapping_Turtle_Cranium.stl

EZPZ Pegboard Hook // 5mm Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 5mm depth. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Hyperdodecahedron // Folding Polyhedra Pack No.1

This 4 dimensional dodecahedron prints flat and then folds and snaps into place! That means you can get cool multicolor parts on all faces with simple color swaps as well as crazy geometry without support material!

This is a freebie from my [Folding Polyhedra Pack No.1](https://www.myminifactory.com/object/3d-print-folding-polyhedra-pack-no-1-81865)

folding-polyhedra-pack-04-dodecahedron-dodecahedron-hyperplus.stl

EZPZ Pegboard Hook // 10mm Reinforced Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 10mm depth and a reinforcing strut along the bottom, which takes up a bit more space in exchange for greater strength. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Snapping

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Momentus Mind Camera Basic // Fidget Clicker + Memory Device

Snappy Switch Keychain

EZPZ Pegboard Hook // 25mm Reinforced Hook

EZPZ Pegboard Hook // 20mm Hook Type B

Big Snappy Indicator Switch

Icosahedron Pyramids // Folding Polyhedra Pack No.1

EZPZ Pegboard Hook // 20mm Reinforced Hook

EZPZ Pegboard Hook // 15mm Hook

EZPZ Pegboard Hook // 20mm Hook

EZPZ Pegboard Hook // 25mm Hook

Snapping Turtle Skull

EZPZ Pegboard Hook // 5mm Hook

Hyperdodecahedron // Folding Polyhedra Pack No.1

EZPZ Pegboard Hook // 10mm Reinforced Hook

Momentus Mind Camera PRO // Fidget Clicker + Memory Device

EZPZ Locking Coathanger Hook

Skull Snapping Turtle

Polypanels // Coral Lithophane (Reaction Diffusion Luminaire)

Polypanels // Square

Polypanels // PLAY Triangle