A knitting project for those of us that can’t knit.

See here for video: https://youtu.be/uQI1Cdas2Jg

Other Round Textile Bowls you might like:
Garter Knit  (Circumferential): https://social.thangs.com/m/507033 
Garter Knit (Vertical): https://social.thangs.com/m/507034
Rib Knit: https://social.thangs.com/m/450318
Regular knit: https://social.thangs.com/m/304075
Braided: https://social.thangs.com/m/348734 
Wicker (Vertical Stakes): https://social.thangs.com/m/475748  
Wicker (Circumferential Stakes): https://social.thangs.com/m/475733


Knitted Bowl

A knitting project for those of us that can’t knit.

This pattern is for a pair of short fingerless gloves. This 3D printed model will require some basic sewing skills. There are three sizes - Small (13cm at wrist), medium (18cm at wrist), and large (21cm at wrist). There will also be some variation depending on what mesh fabric you print on, in addition to what fabric you use as the lining. I prefer using this superfine 4 way powermesh found on amazon - https://a.co/d/dTW0w4M

The 3mf file contains settings and all three sizes. If you'd like to download a single size, make sure to get both side 1 and side 2. This model is .72mm tall. Print this at .24mm layer height with a .4mm nozzle. I print at 35mm/s for the first layer, and 50mm/s per second on the other two layers. If you are using a thicker mesh fabric, use a larger layer height to avoid the snagging of fabric.

I use a magnetic PFLAT sheet found at www.kaizen3dprints.com but you can also use a textured build plate if you'd like, or other sticker print plate variations.

The pause command is entered at layer two, where your fabric and magnets are placed and a little tension on the fabric is applied. The print resumes and will finish after layer 3. Remove side 1 of your size, and reprint side 2. These are simply mirror copies of each other.

Once both prints are finished, find a base fabric of your choosing (velvet, satin, stretch denim, velour etc) and cut a matching piece leaving around 1/2" of seam allowance. Pin the 3d printed mesh on top. Sew a straight stitch with a zipper foot all the way around side 1, fully attaching the lining and 3d printed mesh together. Sew as close to the 3d printed material as you can.  Repeat for side 2. Line up both sides, right sides together (3d printed sides facing each other) and pin both sides together, preparing for a zig zag stitch. Using a zig zag stitch to increase the gloves flexibility, sew the sides and the small portion between your thumb and fingers. Trim away the excess fabric outside of the zig zag stitch. Leave the top, bottom, and thumb holes. You can either create a small hem for these three areas, or trim them off directly adjacent to your straight stitch. Fold the glove right side out, and enjoy your hard work! If you'd like a set of gloves, simply repeat this process!

If you have any questions please send an email to Kaizen3DPrints@gmail.com

Short fingerless gloves

short fingerless gloves 3 sizes.3mf

When I saw the Strong TPU Strap by Turbopstros (https://www.printables.com/model/1451354-strong-tpu-strap-parametric), I had a vision. That's where this bag comes in. I created my version of the TPU strap which is in this file. 
Join me in creating a stunning, unique tote bag with this 3D-printed kit! This project combines 60 PLA flat rings with flexible TPU straps and a sturdy 3D-printed bag base to form a chic, interwoven design. The final product is a durable and stylish bag, perfect for carrying your essentials. If you choose, you can add a lined pouch for added privacy.

This design is a great way to blend 3D printing with crafting, using simple leather rivets to hold the beautiful braided structure in place.

Assembly Instructions (Braiding and Riveting)
Materials Needed:

60 x PLA Flat Rings (Included in file)
1 x Bag Base (Included in file) printed with fuzzy skin
TPU Strips (Print 4 of the included TPU strip file)
2 pieces @ 43" (Handle Strips)
5 pieces @ 25.5" (Horizontal Body Strips)
8 pieces @ 13" (Vertical Body Strips)
34 pairs of 6mm leather rivets

Tools: Hole punch, scissors, and rivet pliers (recommended for easier access).

Detailed Video Instruction: For a step-by-step visual guide, please check out the linked video instruction on my YouTube channel

Assembly Steps:

Prepare the Strips: Cut the 4 printed TPU strips into the lengths specified above for the handles, horizontal body, and vertical body strips.

Attach Handles and Vertical Strips to Base: Slide the 2 handles and the 8 13-inch strips into the slots around the bag base. Punch holes and attach these strips evenly around the perimeter of the bag base using a total of 24 leather rivets (12 pairs). Ensure the strips are secured.

Start the Braiding (Horizontal): See video.  After each round, you'll need to connect the 25.5 inch strip with a pair of rivet. 8 pairs on each side of the bag. 

Weave and Secure the Rings: Continue adding the PLA rings and weaving the horizontal strips, working your way up the bag. The rings should be held in place by the tension of the interwoven strips.

Secure Horizontal Strips: Once the main body is woven, secure the ends of the five horizontal strips to a vertical strip or the bag base using the remaining 12 leather rivets. The weaving action itself is the primary mechanism holding the bag together.

Interwoven Rings and Strap Tote Bag

straps and circle bag.3mf

This is a bundle of STL glove patterns to be used as negative modifiers and3D textile patterns. Please reference the negative modifier guide included. This allows you to create custom gloves using any pattern you'd like. In the photo example, the new Escher inspired pattern is used - https://than.gs/m/1303742

You will need basic sewing skills - please reference the included videos for additional instructions.

If you have questions please email me at kaizen3dprints@gmail.com


Glove Negative Modifiers - 4 Sizes - 3 variations

XS (Child) fingerless glove 350x350 negative modifier.stl

Ever wanted the best part of quilting where you mix colors, fabrics, and patterns but without the sewing?

With the Quilt Pattern Fidget Clicker Keychain you get to play with endless combinations and create unique quilt designs with just a click. Choose **one or four clickers**, experiment with colors, and watch your quilt come to life with no stitching required.  It is all the fun and none of the threading!

For extra stability, add a small dab of superglue to the base of switch so it sits firmly in place. It also fits a ball chain keychain so you can easily attach it to your bag or keys.

**This design requires an AMS.**

**Print Settings**
- No brims required
- No supports required
- 15% infill.
- 2-3 walls
- 0.4mm nozzle
- 0.12mm layer height

**Items Used:**
Pink: https://amzn.to/4hJLeJt
Pink: https://www.matterhackers.com/store/l/175mm-pla-filament-pink-1-kg/sk/M81ZR601?aff=7646
Dark Yellow: https://amzn.to/4fEIxYf
Tan: https://www.matterhackers.com/store/l/pro-series-pla/sk/MZE7T0ST

**Assembly Video:** https://youtu.be/Py1mjyTdV6c

Quilt Pattern Fidget Clicker Keychain – Mix, Match, and Create Modern Quilts, AMS Required

pixelandpapier__quilt_clicker__AMS.3mf

pixelandpapier__quilt_clicker_v2__AMS.3mf

### **Overview**  
This floss bobbin started as a community request and was redesigned for 3D printing efficiency.  
It cuts filament use without losing strength and costs about two cents to print.  
You can make as many as you need, right when you need them.&nbsp;  

---

### **Printing Tips**  
**Printing Technology:** FDM
**Layer Height:** 0.2 mm
**Perimeters:** 4
**Infill:** 10%
**Infill Pattern:** Gyroid
**Recommended Material:** PLA, PETG, ABS
**Supports:** No
**Support Type:** None

**Notes:**  
- Concentric infill used for strength  

---

### **Assembly Instructions**  
**Materials Needed:**  
None  

**Instructions:**  
1. Print
2. Wind thread

---

### **Connect with Lunar Prototypes**  
Like what we’re doing? [Support the project on Patreon](https://patreon.com/LunarPrototypes). Even free members get early previews and project updates.&nbsp;  

Follow on [Instagram](https://www.instagram.com/lunarprototypes) or [YouTube](https://www.youtube.com/@lunarprototypes) for new releases and behind-the-scenes projects.&nbsp;  

Got a feature idea or found a bug? [Join the Discord](https://discord.gg/RdCvuQZbSj) to help shape the next update.&nbsp;  

---

**Tags:** thread, embroidery, sewing, bobbin, string  

**License:**  
Creative Commons Attribution—Noncommercial—No Derivatives (CC BY-NC-ND 4.0)  


Sewing

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Knitted Bowl

Short fingerless gloves

Interwoven Rings and Strap Tote Bag

Quilt Pattern Fidget Clicker Keychain – Mix, Match, and Create Modern Quilts, AMS Required