3 little planters

Pot waffel design.stl

True fruits watering can

**A watering can attachment for a True Fruits bottle.**
The top can be filled up without having to unscrew it. I had problems with watering cans that are too big for the sink and this one can be kept horizontal and therefore is easier to fill.

Size: 60 x 60 x 120 mm
This is the V2

**Print settings**
Required build volume: 60 x 60 x 120 mm
Material usage: 45g
Print time: 4h-5h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm – 0,28mm
Outer walls: 3
Infill: 20%
Build plate adhesion type: a brim if you have bad bed adhesion

Watertight printing - If you have a well set up machine it comes automatically - Otherwise here are some tips: Increase your wall count (at least 3), level your bed nicely, decrease print speed, increase layer height (at least 0.2mm), check your seam quality, calibrate your e-steps and fine tune your retraction settings to make sure no holes appear after a layer change.

If you experience any problems, please feel free to contact me on twitter or Instagram

Rock Planter

rock-planter-cube.stl

EGGIA planter

EGGIA planter.3mf

rock-planter-round-small.stl

Cute Planter Lina - Vasemode

Hey,
this is Lina. Timo will take good care of your plants.

Print with supports.

Cute Planter Lina

Butterfly Stand for planters and stuff!

Butterfly Base.stl

Zig Zag Planters (4 variations)

Zig Zag Planter Alpha.stl

DOLCE  |  Indoor Planter Pot

DOLCE-planter-Pot-Ø12cm.stl

PISA  |  Self-Watering Planter

PISA_Planter_Pot.STL

Owl planter with tree stand

Owl.stl

Watering can

watering_can_1,3L.stl

120-Cell Polychora Planter

This Polychora Planter is derived from the four-dimensional 120-cell 4-polytope, or polychoron.

The 120-cell is one of six regular convex four-dimensional shapes. It is composed of 120 dodecahedral cells. 

4-polytopes cannot be seen in three-dimensional space due to their extra dimension, but there are several techniques that can be used to “project” 4-polytopes into three-dimensional space. This design uses the cell-centered stereographic projection method, chosen for the interesting aesthetic appearance.

While these three-dimensional shapes have curved faces and edges of various lengths, it is interesting to imagine that in four-dimensional space, the faces are flat, and the edges are straight and identical in length.

In this design, select cells have then been removed to allow better visualization of the inner cells, and the outer cells have been hollowed for uses as planters of containers of some kind.


Llama succulent planter

Llama for your succulents! Has drain holes. Would recommend as little support as possible because it is a nightmare to get out from underneath if too thick.

Cute Planter Tim Vase Mode

Hey,
this is Tim.Tim will take good care of your plants.

Print upside down with supports.

Gardening & Landscaping

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

3 little planters

True fruits watering can

Rock Planter

EGGIA planter

Rock Planter

Cute Planter Lina - Vasemode

Butterfly Stand for planters and stuff!

Zig Zag Planters (4 variations)

DOLCE | Indoor Planter Pot

PISA | Self-Watering Planter

Owl planter with tree stand

Watering can

120-Cell Polychora Planter

Llama succulent planter

Cute Planter Tim Vase Mode

LENTRA Planter with Legs | Modern 3D Printable Plant Pot with Drainage Holes

Planter “Extra”

1x1 Planter Square - MagSquares

Meva - a versatile planter (wall or table)

Modular Indoor Hydroponics system