Printed ok from the 3MF(Pokeball A-12page), some minor issues with the flange on the bottom right side, definitely had issues with the pages breaking, even tho i use similar brands. Read the comments and looked at the pdf after and saw the 3MF settings are different than what the pdf said...hopefully my personal settings fix the page issue, but for this flange it will definitely wear out over a few times opening. On to the next book.
By chance, is it just the Poke Ball snap version?
Im having the same issue. The white section doesn't stay in place.
My rocket versions don't seem to have this problem.
By chance, is it just the Poke Ball snap version?
Im having the same issue. The white section doesn't stay in place.
My rocket versions don't seem to have this problem.
Print in place cover was great, pages don't slide well and sometimes get jammed. Had to scrap 5 whole pages because they wouldn't slide and got locked into place, then broke when separated.
The PDF files explained everything I needed—thank you!
These card books are incredible, and all of my friends keep asking about them. I just started printing the OP book, and I'm beyond excited to put it together. Seriously, thank you for sharing these gems!
I know I can paint it myself—and I probably will after I knock out a few copies for the homies and myself—but I was wondering if you happen to have a black version of the OP card book readily available?
hi, how can i take out the one that gets on the bottom? can you make a tutorial? one of my favorite cards is that one and i cant grab them withouth breaking the album (sorry for my bad english)
I want to love this product, everything works seamlessly save for one feature:
On the 12p book. When you fan out the cards, if you try to hold them to look at the cards, the card pages pop out because they naturally bend once they are fanned out.
Can you make some kind of mechanism to finally lock the pages in once they're clicked together?
can't move to commercial tier until these fixes are made unfortunately. And I may need a refund on the basic tier because this product doesn't work as is
Thank you for reaching out and for your honest feedback. I completely understand how frustrating it is when a specific feature doesn't perform as expected, especially when you love the rest of the design!
The issue with the pages popping out when fanned is typically related to printing tolerances, which can vary based on the specific printer, filament, or slicer settings being used. Because the pages are loaded with toploaders, they carry extra weight and stiffness, making precision
To give you some reassurance, the design itself is mathematically sound and fully functional. We currently have hundreds of creators globally printing and selling this design successfully—for instance, one seller in the US has already sold over 2,000 Poke Books!
That being said, I want to make sure it works perfectly for you. I actually just released an update a few days ago specifically addressing this. It includes a detailed PDF guide with the exact printing parameter
I am fully committed to helping you get this running perfectly so you can confidently step up to the commercial tier. Let me know your setup details, and we’ll get this sorted out!
Hello! Thank you so much for your quick response. I am using a P1S, with elegoo PLA+. Filament supply around me is spotty so I will be switching things up once and a while. I am not super technical, so if adjusting my flow rate or expert calibration, etc, on an ongoing basis is the only way for this print to work because the tolerances are that tight, it just might not be the right print for me. I couldn't tell you why the print didn't work, only that the tolerances ARE off on my print.
I could take a screenshot of what my settings are, but I downloaded the model and PDF yesterday. One thing wasn't certain, in the guide it says nothing about walls in the top but under the customization section you talk about 1 wall etc in a small comment.
I was able to change my bridge direction to 90 degrees. But there also isn't a print profile on my slicer for 0.20mm High Quality. Only Strength and Standard
Thank you for the design, but I encounter some problems. I print the 12 Page Cover Print in Place - A, but the hinge are too loose so it detach right away. I already change the seam from aligned to random, but the problem is still occur. is there any solution to this problem? i did not change any settings from the bambu lab file. I'm using Bambu Lab A1. Thank you so much!
We noticed that users printing with the Bambu Lab A1 have been experiencing a specific issue. After running several tests, we confirmed that this doesn't happen with other Bambu Lab models or different printer brands; the cover peeling off seems to be unique to the A1.
Don't worry, though—I am already tweaking the file to fix this!
The updated version will be released in the next few days, and it will also include the brand-new 9-page and 15-page options.
Absolutely love the design! Great idea! My son has already printed all three and cannot pick a favorite! Any chance of doing a One Piece variation/design?
Do you have any tips/suggestions on preventing the black from stringing or blobbing onto the white? Occasionally I'll get very faint black carryovers on subsequent layers which are visible through the first white layer that kind of ruin the entire print 😢 otherwise love the design!
I seem to have consistent issues with the Poke Ball, Snap Fit Version, Back cover.
The white section doesn't seem to hold in place as well as the Red section.
Rocket back cover doesn't seem to have this issue.
Anyone else?
This is happening to me too but it's the red section. Basically just falls out. I printed the Poke Ball - A version, print in place. Is there a fix for this?
I love the print. It assembled great. But I do have one small improvement. for the pokeball and ultraball the inside of the covers are all black, with the default number of bottom layers you can see the black infill through the white filament...I am even using matte white which should help with this. Can you please only make the first few layers black and then the rest white. or make the black part of the pokeball separate from the inside covers?
Hi there, that’s quite strange, as it is the same file for everyone and no one else has encountered this issue. If you used the 3MF file for Bambu Lab, everything should already be pre-configured. However, if you used the STL file, did you split the design into separate parts before coloring the individual components?
Hello, here in Japan the Top Loaders are a bit larger, they need to be +0.2mm in height and +0.8mm in width. Could you make the file available for me to edit?
Hi there, as mentioned in the product description, you need to use Ultra PRO Regular Toploaders. Please ensure you are using this specific model to guarantee a perfect fit.
I’ve bought 3 different boxes of ultra regular top loaders and none of them are even close to fitting. So everyone know that you will likely have to scale up
Something in my print is not working properly. I have already had to cancel the print three times because of the bed adhesion on the corners of the FRONT plate.
Bambu Lab A1
Bambu Lab PLA Lite
I started with the Simple Rocket book cover print in place but it did not fold. Unsure what the issues were printing this? Suing bamboo labs pla matt black with the standard setting usijng the X1C Carbon. Any ideas how to solve this?
I printed the design so far. I like it. But was wondering if there is a version where the pages flip more like a book? Like the ones you have for your photo albums. Keep up the awesome work!
is there a way to see what models i've downloaded. according to the sub i have 4 models a month but ive only downloaded 3 and now it's telling me to upgrade to download another one.
This is a great quality, high-value product! If I may point out two issues I would love to see corrected:
The holes for the magnets are too large. The instructions call for 6x2mm magnets, but the holes are more than 7mm in diameter. I would love to see it come down to 6.1mm; it would make fitting the magnets so much easier than having to mess with super glue.
The PokeBook 12 Page A (Premium), only fits 11 pages. When I put the 12th in it, the book will not close. Can you please fix this?
The starting model is always the same, except for the front design. So this problem isn't related to the model, but rather to the filament used. When the pages are closed, check the left side of the page where the guides correspond. Depending on the filament, the bridge will be more or less precise. I recommend closing the pages and pressing them together firmly with your hands, or pushing the bridge upwards with your fingernail. Let me know if you solve the problem!
Good morning,
Thank you so much for your feedback. After checking, I can tell you that:
From the CAD, I can confirm that the magnet holes are all 6.4mm and don't vary from one model to another. The slicing process likely changed the dimensions slightly. I used BambuStudio and didn't encounter this problem.
I also am encountering issues with the magnet size being too large on the page. Not the cover, but the magnet hole on the page specifically is too large. Any suggestion here?
Hello new to 3d printing and just downloaded this file. Is there anyway of printing it with a P1S because it keeps throwing a error that the print file isn't compatible.
I've just downloaded this file for my P1S and not having this issue, but if you're new to 3D printing, I'd try an easier print for your first few to get used to how the slicer works and all that!
Seeing some issues in rocket ball 6pg snap fit. Getting some gashes in it. Had no problem with the regular poke ball variation A. Wondering if it’s the speed of the rocket print. Any suggestions?
Discussions — CARD BOOK | TRADING CARD BINDER
Great Design! Already printed all three and they look and work perfectly. Any chance a One Piece version could be in the future?
Thank you so much🔥😍 yes maybe!!
How'd you print without damaging sliders
Hello,the Toploaders from German Brand DeckWächter works perfect too :) !
Hello! Thanks for your feedback!
Do you recommend using the matt white ESUN filament on this one too ?
Yes i always use esun pla (pla or pla matte is the same). Please read the PDF files with the tips
Hi, the hinge of the cover isnt strong enough, pulls apart too easily, any tips to fix it? Im printing on an A1, thanks
Added a custom pattern to resemble a Road Poneglyph for One Piece TCG cards :)
Thanks for sharing the design and for adding a blank one!
twice now ive printed the covers and they keep coming apart. is there anything im doing wrong? they just snap out
By chance, is it just the Poke Ball snap version? Im having the same issue. The white section doesn't stay in place. My rocket versions don't seem to have this problem.
coming apart how so? as in not staying snapped together? im about to print this next
Happened to me too
By chance, is it just the Poke Ball snap version? Im having the same issue. The white section doesn't stay in place. My rocket versions don't seem to have this problem.
You spend a lot of time on this design, and it's amazing
Thanks😍🔥
Amazing model, prints great!
Thanks❤️🔥
Print in place cover was great, pages don't slide well and sometimes get jammed. Had to scrap 5 whole pages because they wouldn't slide and got locked into place, then broke when separated.
The PDF files explained everything I needed—thank you!
These card books are incredible, and all of my friends keep asking about them. I just started printing the OP book, and I'm beyond excited to put it together. Seriously, thank you for sharing these gems!
I know I can paint it myself—and I probably will after I knock out a few copies for the homies and myself—but I was wondering if you happen to have a black version of the OP card book readily available?
hi, how can i take out the one that gets on the bottom? can you make a tutorial? one of my favorite cards is that one and i cant grab them withouth breaking the album (sorry for my bad english)
Hello! Just use the tip of a knife or even just a sheet of paper. I personally manage with my fingernail.
I want to love this product, everything works seamlessly save for one feature:
On the 12p book. When you fan out the cards, if you try to hold them to look at the cards, the card pages pop out because they naturally bend once they are fanned out.
Can you make some kind of mechanism to finally lock the pages in once they're clicked together?
can't move to commercial tier until these fixes are made unfortunately. And I may need a refund on the basic tier because this product doesn't work as is
Please note that the card pages are loaded with toploaders too.
Hi there,
Thank you for reaching out and for your honest feedback. I completely understand how frustrating it is when a specific feature doesn't perform as expected, especially when you love the rest of the design!
The issue with the pages popping out when fanned is typically related to printing tolerances, which can vary based on the specific printer, filament, or slicer settings being used. Because the pages are loaded with toploaders, they carry extra weight and stiffness, making precision
fit even more critical.
To give you some reassurance, the design itself is mathematically sound and fully functional. We currently have hundreds of creators globally printing and selling this design successfully—for instance, one seller in the US has already sold over 2,000 Poke Books!
That being said, I want to make sure it works perfectly for you. I actually just released an update a few days ago specifically addressing this. It includes a detailed PDF guide with the exact printing parameter
wall counts, and calibration settings needed to achieve a perfect, secure lock.
Could you please double-check if you have downloaded the latest version and reviewed the updated PDF guide?
Additionally, to help me troubleshoot this with you, could you let me know:
What 3D printer and filament brand/type (e.g., PLA Matte, PLA+, etc.) you are using?
If you have calibrated your flow rate or X/Y hole compensation, as even a 0.1mm variance can cause the snaps to lose their grip when under tension.
I am fully committed to helping you get this running perfectly so you can confidently step up to the commercial tier. Let me know your setup details, and we’ll get this sorted out!
Best regards, ALFI
I redownloaded the file, it's the same. What do you suggest as my next course of action?
Hello! Thank you so much for your quick response. I am using a P1S, with elegoo PLA+. Filament supply around me is spotty so I will be switching things up once and a while. I am not super technical, so if adjusting my flow rate or expert calibration, etc, on an ongoing basis is the only way for this print to work because the tolerances are that tight, it just might not be the right print for me. I couldn't tell you why the print didn't work, only that the tolerances ARE off on my print.
I could take a screenshot of what my settings are, but I downloaded the model and PDF yesterday. One thing wasn't certain, in the guide it says nothing about walls in the top but under the customization section you talk about 1 wall etc in a small comment.
I was able to change my bridge direction to 90 degrees. But there also isn't a print profile on my slicer for 0.20mm High Quality. Only Strength and Standard
im sorry if im missing something, but where are the instructions to customise as it says in the pictures?
Redownload the files :) it’s a PDF
Thank you for the design, but I encounter some problems. I print the 12 Page Cover Print in Place - A, but the hinge are too loose so it detach right away. I already change the seam from aligned to random, but the problem is still occur. is there any solution to this problem? i did not change any settings from the bambu lab file. I'm using Bambu Lab A1. Thank you so much!
We noticed that users printing with the Bambu Lab A1 have been experiencing a specific issue. After running several tests, we confirmed that this doesn't happen with other Bambu Lab models or different printer brands; the cover peeling off seems to be unique to the A1.
Don't worry, though—I am already tweaking the file to fix this!
The updated version will be released in the next few days, and it will also include the brand-new 9-page and 15-page options.
Thank you so much for your feedback!
thank you for your reply! may I ask, is the version updated yet? where can I see the announcement for it?
Any chance of getting a 9 page version? Pleaseee
YES! next day :)
When will it be ready? Will there be a notification so I can keep an eye out and download it again? Thanks
Absolutely love the design! Great idea! My son has already printed all three and cannot pick a favorite! Any chance of doing a One Piece variation/design?
Yes! Look now the design!
Why is all the models blank? I printed out the Blank one to test it out but the master book, poke book and team rocket book is blank as well?
Do you have any tips/suggestions on preventing the black from stringing or blobbing onto the white? Occasionally I'll get very faint black carryovers on subsequent layers which are visible through the first white layer that kind of ruin the entire print 😢 otherwise love the design!
I seem to have consistent issues with the Poke Ball, Snap Fit Version, Back cover. The white section doesn't seem to hold in place as well as the Red section. Rocket back cover doesn't seem to have this issue. Anyone else?
This is happening to me too but it's the red section. Basically just falls out. I printed the Poke Ball - A version, print in place. Is there a fix for this?
I love the print. It assembled great. But I do have one small improvement. for the pokeball and ultraball the inside of the covers are all black, with the default number of bottom layers you can see the black infill through the white filament...I am even using matte white which should help with this. Can you please only make the first few layers black and then the rest white. or make the black part of the pokeball separate from the inside covers?
I can’t find pink color with Master book. It is not same image
Hi there, that’s quite strange, as it is the same file for everyone and no one else has encountered this issue. If you used the 3MF file for Bambu Lab, everything should already be pre-configured. However, if you used the STL file, did you split the design into separate parts before coloring the individual components?
Hello, here in Japan the Top Loaders are a bit larger, they need to be +0.2mm in height and +0.8mm in width. Could you make the file available for me to edit?
Hi there, as mentioned in the product description, you need to use Ultra PRO Regular Toploaders. Please ensure you are using this specific model to guarantee a perfect fit.
can we get a one piece theme one ? :)
You can customize the BLANK book using the slicer by adding SVG images and personalizing it however you like!
Love this design, but is there a chance you could improve the little nubs that keep the hinges in place? Maybe a little bit bigger?
I just have a small doubt does the print automatically stop for inserting the magnet or do we need to make it stop? or you just glue it in?
I’ve bought 3 different boxes of ultra regular top loaders and none of them are even close to fitting. So everyone know that you will likely have to scale up
Ultra•TOP regular, look at the pictures, there is the one you need to buy. Write me on Instagram or email please
Something in my print is not working properly. I have already had to cancel the print three times because of the bed adhesion on the corners of the FRONT plate. Bambu Lab A1 Bambu Lab PLA Lite
I started with the Simple Rocket book cover print in place but it did not fold. Unsure what the issues were printing this? Suing bamboo labs pla matt black with the standard setting usijng the X1C Carbon. Any ideas how to solve this?
I printed the design so far. I like it. But was wondering if there is a version where the pages flip more like a book? Like the ones you have for your photo albums. Keep up the awesome work!
any chance of getting a 9 page version?
is there a way to see what models i've downloaded. according to the sub i have 4 models a month but ive only downloaded 3 and now it's telling me to upgrade to download another one.
go under your profile, then "view my models" then click "purchased", it will show you everything youve downloaded
Hello! Mmm I don’t know sorry! If you have any problems, please write to support@thangs.com Thank you
is it not possible for you to see how many i've downloaded?
No I can’t sorry :( please contact thangs!
any plans to make more pokemon card models?
This is a great quality, high-value product! If I may point out two issues I would love to see corrected:
Good morning, Thank you so much for your feedback. After checking, I can tell you that:
I also am encountering issues with the magnet size being too large on the page. Not the cover, but the magnet hole on the page specifically is too large. Any suggestion here?
Hi, thank you for the quality of the models! I was out of white PLA and made it in PETG, but it came out too tight. The Bridge 90.
Hi! I recommend reading the PDF file carefully. I've never printed it in PETG.
do i need support for this print? my print failed at the overhanging parts
NO SUPPORTS
any advise on how to print over hangs better?
All infos are in the PDF files
Hello! Is the color information included in the stl file? Or how can I get the multicolor information?
Hello, all infos are inside the file!
Hello, I am wondering which brand of filament you are using for purple. The colour in your photos is amazing!
Purples from Snapmaker and pinks from eSun, both matte PLA
does this work for the A1 mini?
Yes
Hello new to 3d printing and just downloaded this file. Is there anyway of printing it with a P1S because it keeps throwing a error that the print file isn't compatible.
I've just downloaded this file for my P1S and not having this issue, but if you're new to 3D printing, I'd try an easier print for your first few to get used to how the slicer works and all that!
yea youtubed it and figured it out pretty quick.
Hello! Impossibile I create the file .3MF for BambuLab printers!
I recommend you learn how to use the slicer, try watching some videos on YouTube!
Thanks ALFI
Seeing some issues in rocket ball 6pg snap fit. Getting some gashes in it. Had no problem with the regular poke ball variation A. Wondering if it’s the speed of the rocket print. Any suggestions?
Hi! The files are the same, just separated. So I don't think it's a model issue!