Introducing my version of Cloud's Buster Sword from Final Fantasy VII with a 1/2 inch diameter PVC cavity in the handle that goes partly into the blade base for support.  This is to keep it from being too heavy once assembled. PVC should be cut to 12 inches (304.8 mm) long.

Overall size: 54.72 inches (1390 mm) x 8.54 inches (217 mm)

Buster Sword

FF7_Bustersword_Crossguard.stl

FF7_Bustersword_Handle.stl

FF7_Bustersword_Blade_1.stl

FF7_Bustersword_Blade_2.stl

FF7_Bustersword_Blade_3.stl

FF7_Bustersword_Blade_4.stl

FF7_Bustersword_Blade_5.stl

Introducing my version of the Confuso Sword from Clair Obscur Expedition 33 with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to around 36 inches (914.4 mm). The bambu file has the sword sliced into smaller parts to fit into the build volume as a starting point.

Confuso Sword

Exp33_Confuso_Sword.stl

Introducing my version of the Confuso Dagger from Clair Obscur Expedition 33 with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to around 8 inches (203.2 mm) to fit into the handle and blade.

Confuso Dagger

Exp33_Confuso_Dagger.stl

Exp33_Confuso_Dagger_Handle.stl

Introducing my version of the Spectra Swallow used by Serge in Chrono Cross! It is print in place with no minimal supports. This was made with a 1/2 inch diameter PVC cavity in the handle for support. You may need to use a brim for better stability while printing.

You will need to print x1 of everything except the following:
Blade Top x2
Blade Bot x2

For assembly PVC should be cut to about 36 inches (914.4 mm). Glue the two parts of each blade top and bottom together to have two whole assembled blades. You can put in the PVC core as you assemble the handle then attach the assembled blades on either side. 

Make sure the triangle "keys" on the handle are facing in opposite directions as this pertains to how to line up the blades as well. When attaching the blades to the handle make sure the triangle keys are lined up. When you have them lined up the triangles should be on the "backside" of each blade and the blades will face in opposite directions on the handle. See image for visual alignment.

Spectra Swallow

CC_Spectra_Handle_A.stl

Introducing the Agony Axe used by Spawn! It is print in place with minimal supports. This was made with a 1/2 inch diameter PVC cavity in the handle for support. You will need to use supports for the head, pommel, and handle parts. The axe and handle parts you may need to use a brim for better stability while printing.

You will need to print x1 of everything except the following:
Key Joint x6
Axe Top x2
Axe Bot x2

For assembly PVC should be cut to about 24 inches (609.6 mm). Glue the two parts of each axe top and bottom together using the key joints to have two whole assembled axes. You can put in the PVC core as you assemble the pommel, handle, and head of the axe then attach the assembled axes on either side.

Agony Axe

Spawn_Agony_Axe_Top.stl

Introducing my version of the Soul Reaver Sword from Legacy of Kain series with a 1/2 inch diameter PVC cavity in the handle for support. You will need to use supports for the skull and the skull wings. The blade parts you may need to use a brim for stability while printing.

You will need to print x1 of everything except the following:
Key Joint x4
Skull Wing x2

For assembly glue the two halves of the skull together and attach the skull wings afterwards. PVC should be cut to 12 inches long. You can put in the PVC core for the handle in when you assemble the hilt. Everything else should be pretty straight forward. 

Update 1/24/24
Added the Skull_whole stl file as another option instead of printing two halves if preferred.

Soul Reaver Sword

Soul_Reaver_Skull_Front.stl

Soul_Reaver_Skull_Back.stl

Soul_Reaver_Skull_whole.stl

Introducing the Dark Rapier used by Rose from Legend of Dragoon! This sword prop has a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to 24 inches (609.6 mm). You may want to use a brim just for bed adhesion and minimal supports for the handle part.

Overall size: 39.95 inches (1014.78 mm) x 6.73 inches (171.10 mm)

Rose Dark Rapier

LoD_Rose_Dark_Rapier_handle.stl

Introducing the Xenoknight Greatsword I made to go with my Xenoknight armor! This is sized to be about 5ft tall with a 3/4 inch diameter PVC cavity in the sword for support. PVC should be cut to 60 inches (1524 mm) .

Xenoknight Greatsword

greatsword_blade_1.stl

Introducing my version of the Fenrir Keyblade from Kingdom Hearts with a 3/4 inch diamater PVC cavity in the handle and blade for support. PVC should be cut to 28.8 inches (731 mm) long. 

Fenrir Keyblade

Fenrir_Handle.stl

Fenrir_KeyChain.stl

Introducing the Mage Staff inspired by Vivi from Final Fantasy IX. This is sized to be about 4.5ft tall with a 3/4 inch diameter PVC cavity in the handle for support. PVC should be cut to 48 inches (1219.2 mm).

Mage Staff

Mage_Staff_Top.stl

Introducing the 4-Point Shuriken famously used by Greninja in Pokemon but as an extra large fidget spinner! It is print in place with no supports needed. I also included 2 variations of the center so you can build it with a handle bar or no handle bar.

Overall Assembled Size: 18.5 inches (470 mm) x 18.5 inches (470 mm) x 0.inch (12.50 mm)

You will need to print the following of each part.
Handle x1
Blades x4
Bearings Cover x2 (optional)

*Build Instructions*
1) Glue x2 blades together to make half the shuriken (then let the glue set)
2) Glue second set of blade together to make the second half (then let the glue set)
3) Place the handle and bearings inside both halves of the shuriken and glue together (then let the glue set)
4) Glue the bearings covers to the center handle on either side. The covers are not required but can help to prevent bearings that may fall out on the bottom side depending on how you hold it. You could just use the one cover on that side instead of both. As using both does restrict the spinning duration because of more friction.
5) Once the glue is completely set you're all done and can spin to your heart's content, enjoy!

4 Point Shuriken Spinner XL

4Point_Shuriken_Spinner_Blade.stl

4Point_Shuriken_Spinner_Handle_bar.stl

4Point_Shuriken_Spinner_Bearings_Cover.stl

Introducing the Axel Chakram from Kingdom Hearts but as an extra large fidget spinner! It is print in place with minimal supports. I also included 3 variations of the center so you can build it how you prefer.  I will warn you the cross handle is more accurate for cosplay purposes but it is not that comfortable to hold.

Overall Assembled Size is 20.7 inches (526.5 mm) x 20.7 inches (526.5 mm) x 0.5 inch (12.5 mm)

You will need to print the following number of each part.

Handle x1
Bearings Cover x2 (optional)
Key Joint x8
Kunai Top x8
Kunai Bottom x8
Outside Ring Part A x4
Outside Ring Part B x4

*Build Instructions*
1) Glue x1 key joint into the kunai to bond the top and bottom together
2) Glue x1 whole kunai into the outer ring part A and part B to make 1 section, repeat 4 times to make 4 sections of the outer ring (then let the glue set)
3) Once you have 4 sections assembled, you will glue 2 sections together using x1 whole kunai to make two halves of the outer ring. (then let the glue set)
4) Take one half of the outer ring and glue into the center handle (then let the glue set)
5) Take the other half of the outer ring and attach to the rest of the outer ring that you glued to the handle and using the remaining x2 whole kunai. (then let the glue set)
6) Glue the bearings covers to the center handle on either side. The covers are not required but using them does restrict the spinning duration because of more friction.
6) Once the glue is completely set you're all done and can spin to your heart's content, enjoy!

Axel Chakram Spinner XL

axel_handle_cross.stl

Introducing Rikku's Dagger from Final Fantasy X but as a large spinner! It is print in place with minimal supports. You should only really need supports for the base of Dagger Part A if you want to print it standing up and the underside of the joint this attaches to on the handle.

You will need to print the following number of each part.

x1 Handle
x2 Handle Guards
x1 Dagger Part A
x1 Dagger Part B

Rikku Dagger Spinner

rikku_dagger_handle.stl

Introducing my version of the Brotherhood Sword from Final Fantasy X! with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to 36 inches (914.4 mm). I have two versions of the handle one you can print with the loop and one without the loop. Sword itself should take minimal supports and may need to use a brim for stability printing the blade parts.

Overall Size: 53.61 inches (1361.78 mm) x 10.33 inches (262.58 mm)

Brotherhood Sword

FFX_Brotherhood_Sword_Handle_B.stl

Introducing my version of the True Bankai Zangetsu from Bleach with a 1/2 inch diameter PVC cavity for support.  PVC should be cut to 36 inches (914.4 mm). No supports needed and may need to use a brim for stability printing the blade parts.

Overall Size: 50.17 inches (1274.32 mm) x 7.23 inches (183.71 mm)

True Bankai Zangetsu

Zangetsu_Handle.stl

Introducing the Z-Saber beam sword! Print in place with minimal supports I suggest using brim for stability while printing. This was made with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to 12 inches (304.8mm).

Overall Size: 35.25 inches (896mm) x 9.29 inches (236mm)

Z-Saber Variation B

ZSaber_B_Handle.stl

Introducing the Z-Saber beam sword! Print in place with minimal supports I suggest using brim for stability while printing. This was made with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to 12 inches (304.8mm).

Overall Size: 35 inches (905mm) x 1.6 inches (42.5mm)

Z-Saber Variation A

ZSaber_A_Handle.stl

Introducing the X-Buster arm cannon! This is print in place with no supports needed and includes a built in curved handle. Inside diameter is right at 3.9 inches (100mm) so it should fit most at standard size.

X-Buster

XBuster.stl

Introducing the Fierce-Master Sword a combination of two of the strongest swords from Legend of Zelda with a 1/2 inch diameter PVC cavity in the handle for support. PVC should be cut to 48 inches (1219.2 mm). Sword itself should take minimal supports and may need to use a brim for stability printing the blade parts.

Overall Size: 52.80 inches (1341.29 mm) x 14.13 inches (358.96 mm)

Fierce-Master Sword

FM_Sword_Blade_1.stl

Introducing the 4-Point Shuriken used by Yuffie in Final Fantasy VII but as an extra large fidget spinner! It is print in place with minimal supports needed. I also included 2 variations of the center so you can build it with a handle bar or no handle bar.

Overall Assembled Size: 29 inches (470 mm) x 29 inches (470 mm) x 0.inch (12.50 mm)

You will need to print the following of each part.
Handle x1
Blades x4
Blade Bars x4 (use any combination of the slotted or wrapped)
Bearings Cover x2 (optional)

Yuffie 4-Point Shuriken Spinner XL

FF7_Yuffie_Shuriken_Handle_Bar.stl

Introducing the Buzzed Eldritch Staff to channel your Cthulhu powers when you drink! All you need to print is the top and bot parts then cut a 3/4 inch PVC pipe to whatever length you desire for your staff. Then simply glue the top and bot parts onto the PVC then place your BuzzBall flask of mana in the top of the staff.

Where the neck of the BuzzBall sits has a wider neck than the bottle itself this is for using whatever you want to use to secure the bottle. I envisioned using a ring of 3mm EVA foam to make it snug enough to hold and remove the bottle. But whatever you choose you have some wiggle room for securing it there.

The bottle top will meet the top of the PVC I did this so if you wanted to attach a tube to feed it down through the staff you could without having to tinker with the design.

Buzzed Eldritch Staff

Buzzed_Eldritch_Staff_Top.stl

Introducing the Buzzed Mage Staff to cast your magic spells and get your drink on! All you need to print is the top and bot parts then cut a 3/4 inch PVC pipe to whatever length you desire for your staff. Then simply glue the top and bot parts onto the PVC then place your BuzzBall flask of mana in the top of the staff.

Where the neck of the BuzzBall sits has a wider neck than the bottle itself this is for using whatever you want to use to secure the bottle. I envisioned using a ring of 3mm EVA foam to make it snug enough to hold and remove the bottle. But whatever you choose you have some wiggle room for securing it there.

The bottle top will meet the top of the PVC I did this so if you wanted to attach a tube to feed it down through the staff you could without having to tinker with the design.

Buzzed Mage Staff

Buzzed_Mage_Staff_Top.stl

Weapon Props

Subscribe to support my work and download my digital files for non-commercial use.

5 Downloads per month

*Dice3D Designs digital files are NEVER to be resold, shared, or redistributed in any form.*

Dice Fan

Subscribe to support my work and download my digital files and a commercial license to sell physically printed models of my original designs.

10 Downloads per month

COMMERCIAL LICENSE: Official Authorization to sell 3D Prints of original Dice3D Designs, for as long as you hold an active subscription.

*Dice3D Designs digital files are NEVER to be resold, shared, or redistributed in any form.*

Credit/ Attribution
If you are profiting from these prints I ask that you give me credit as the model source. 

Dice Peddler

Dragoon Wings Ear Cuff

EarCuff_Dragoon_Wings.stl

Xenoknight Armor

bolt_detail.stl

Roll for initiative! I go by my nickname Dice. I will be posting original designs as well as fan art and all files are made by me not AI.

Your membership directly supports me thank you for stopping by!