ChelsCCT (ChelseyCreatesThings)20K followers

Pooping Balloon Dog

5.4K downloads · 4 years ago · License: Attribution-NonCommercial-NoDerivs CC BY-NC-ND *** ***Sculpt by @ChelsC423*** A fun series

This model is restricted by licensing terms.

View license.

Description

License: Attribution-NonCommercial-NoDerivs CC BY-NC-ND

Sculpt by @ChelsC423 A fun series of balloon animals I've always wanted to make! Hope you enjoy!

If you would like to sell physical objects, please see the Chaos Core Partner tier on our Patreon

If you would like to support us and receive exclusive to Patron models every month check us out here: https://www.patreon.com/chaoscoretech

Tags:

Community Makes (12)

I used Lychee Slicer for this print and it was quite finicky.
After a lot of trial and error these are the settings I settled on.
I've attached my resin settings in the photos.
I printed directly on the build plate so there was a slight elephant foot effect which I just sanded off.
If I was going to print this again I'd increase the compensation on the burn in layers to .25.
I've also attached a photo of the model in the slicer with the supports used, I recommend using quite a bit more supports as every single one of the connect areas sagged.
Easily sanded to look much better but would have been easier if I set up more supports.
I would avoid using supports on the torso of the body because they can be a pain to remove.
Super happy with how it turned out.
I airbrushed it with one layer of white all over and topped that with 2 layers of red and some gloss mod podge.
Great model with minimal issues for this odd shape.
Thanks!

very well designed model. had a good chuckle with some friends and family members (mother was not amused lol)

Community Makes (12)

Discussions

Doodles2 years ago

CGorecki Designs2 years ago

maxmicah441 year ago

I used Lychee Slicer for this print and it was quite finicky. After a lot of trial and error these are the settings I settled on. I've attached my resin settings in the photos. I printed directly on the build plate so there was a slight elephant foot effect which I just sanded off. If I was going to print this again I'd increase the compensation on the burn in layers to .25. I've also attached a photo of the model in the slicer with the supports used, I recommend using quite a bit more supports as every single one of the connect areas sagged. Easily sanded to look much better but would have been easier if I set up more supports. I would avoid using supports on the torso of the body because they can be a pain to remove. Super happy with how it turned out. I airbrushed it with one layer of white all over and topped that with 2 layers of red and some gloss mod podge. Great model with minimal issues for this odd shape. Thanks!

PrinterElegoo Mars 3

Print bed sizeX: 143 mm; Y: 6 mm; Z: 175 mm

MaterialStandard

Layer height0.05 mm

Infill density100 %

kyleolsondesign2 years ago

PrinterBambu Lab A1 mini

MaterialPLA

Layer height0.16 mm

Infill density15 %

SupportsTree

nerdmaster1542 years ago

very well designed model. had a good chuckle with some friends and family members (mother was not amused lol)

PrinterBambu Lab X1

MaterialASA

Layer height0.2 mm

Infill density15 %

SupportsTree

hyperfixationscreations2 years ago

rukaduka3 years ago

Is there a file to print just the poop balloon?

michaelbleck962 years ago

if you use orcaslicer, you can split models

anthony.d.macleod3 years ago

I can't for the life of me seem to get this to print properly. It 95% turns out great except for it's but and "mouth" where it the new layer starts, it always seems to mess up and not print/form a hole instead for the first 2-3 layers in justvthose exact locations